Question about Singer 7462 Mechanical Sewing Machine

1 Answer

The tenchon on my sewing machen is too do i ajust it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You need to adjust the tension on the tension dial with is usualy at the front its shaped like a dial. or if its a industrial machine it will be at the top as well as the front u need to turn it slightley to the left . or right.. hope this helps angela

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to take the safty cover off of a husquvarna sewing machene

I suggest getting a service manual that will show the various screws that have to be removed. In general, pull off the hand wheel, remove the screws from the bottom of the machine, and remove the screws from the back side of the machine. You'll need a set of Torx tools (from the local auto store). Also note that the plastic cover pieces snap together and will have to gently pried apart. Don't take off the front cover unless you have to. It's got electrical connections and is much more difficult to reassemble correctly.

Mar 21, 2014 | Husqvarna Viking 1

1 Answer

Zenith sewing machine J-A36 instruction manual

email these sites about a manual

May 21, 2012 | Sewing Machines

1 Answer

I have a consew 230 and it is gathering on the bottom how do i ajust it

Pull the bobbin thread as it comes through the machine. Does it feel too tight? if so check the threading. if threaded correctly and still too tight back off small tension screw 1/2 turn at a time. see if that helps. carefull not to undo too far as the small screw will come right out and may be difficult to put back. This machine is for heavy, stiff fabric. If you're using thin fabrics, stop right there make no adjustment. You'll need a lighter machine. This is for upholstery and leather work. Even curtain/drape fabric may be too light. Thats the best I can do without seeing the machine.

Dec 11, 2010 | Consew 226R2 Sewing Machine

1 Answer

Bobbin thread keeps breaking

Could well be that the bobbin tension is too tight, you should only just be able to pull the bottom thread through with slight resistence, if it is too tight slacken the screw on the bobbin case anti clockwise about a quarter of a turn at a time and test until you get it right,

Mar 05, 2010 | Janome 659 Mechanical Sewing Machine

1 Answer

It dose not pull tight

Bobbin tension, and clean out the feed dog and bobbin area of the thread dust, make sure the tension is set correctly on the upper, and sew, sew, sew.

Sep 26, 2009 | Kenmore 756A-30BH Mechanical Sewing...

1 Answer

White machine bobbin tention ajustment

how do you thread it ?can you give intructions?

Aug 11, 2008 | White Sewing 1521

1 Answer

Brother VX-1120- The needle is not picking up bobbin thread.

I had the same problem with my brother vx-1120 sewing machine. I set the needle to lowest position by using the hand crank. Then I loosened the knerled set screw that holds needle in place. Then I moved needle shaft till the eye of needle is just lower than the hook on the shuttle loop maker. It made my mechine work. There are instuctions for ajusting timing on machine but I think these mechines are built to not fix and throw out. Just because there where no ajustment marks at all on machine, any machanical machine will needed to be ajusted sometime.

Jul 08, 2008 | Brother CS-8150 Computerized Sewing...

Not finding what you are looking for?
Singer 7462 Mechanical Sewing Machine Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Singer Sewing Machines Experts

Bargain Box
Bargain Box

Level 3 Expert

1388 Answers

Cindy Wells

Level 3 Expert

4762 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Singer Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides