Question about D-Link 802.11g Wireless Router WBR-1310 (WBR1310)

2 Answers

Westell 327W15-06 Modem/router password doesn't work- can we reset?

The above says it all. Went on vacation, disconnected from ISP; returned and resubscribed...all would work the same until tried to access modem, and we had forgotten the modem password! ISP won't help cause didn't purchase it from them (Ebay), and Westell DOESN'T HAVE A TECH SUPPORT. Both suggested buying another modem/router from ISP!!! (Of course). Know there is a generic password (factory reset), as used it once, but no one seems to want to give it up. Do you know anyway around this? Any help much appreciated!

Posted by on

  • sflanigan Aug 24, 2008

    I don't seem to know the user name and password for the first time setup....every one says its admin.......but I have tried and it will not let me log on????? any ideas????? a password reset may fix the problem!!!! I really want to secure my wireless!!!!!



  • durana5 Oct 07, 2008

    You had it right! THANKS! It's working now.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

It's either admin/password or admin/1234. Reset the router to factory specs by holding in the reset tab for thirty seconds.

Posted on Oct 07, 2008

Admin
password

Posted on Sep 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need my netgear password


Most of the NETGEAR devices, except ReadyNAS products and Fully Managed switches, have the following default username and password:
  • Username = admin
  • Password = password
    • For older devices, password = 1234
If you have changed the default password and have forgotten it, you will need to reset the NETGEAR device to factory default settings in order to use the default username and password. Click here to learn how to reset the NETGEAR device to factory default settings. Please note: restoring a device to its factory default settings will erase any changes you have saved to the device.

Reset and Restore the NETGEAR device to Factory Default Settings

Symptoms:

  • Forgotten/lost password to log into the NETGEAR device
  • Cannot access the NETGEAR device web interface
Click here for video walk through example of how to reset the WGR614v9 router.
video-icon2.jpg

Resolution:

If you have changed the default password and have forgotten the password, you may need to reset the NETGEAR device to factory default settings.

When a NETGEAR device resets, it goes back to the state when it was new - all information that was entered by hand is lost! Examples include critical things you need to get online, such as ISP username, ISP password, IP addresses, wireless security keys, and ports and services that were opened. It all needs to be re-entered.
So, have your ISP information before resetting the router.
Naturally, if you moved to a new city, or if you bought a used router, the old information in the router may not be of use to you. Contact your ISP if you can't connect any computer directly to the Internet. Then, if there is a connection problem when the router is added, see No Internet Access Through the Router
Reset for most routers with a reset button on the rear panel
Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is admin and the password is either password or 1234. Try these before resetting the router.)
  1. Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
  2. Release the button.
  3. Wait for the router to reboot.
  4. Log in with the default password. If the router configuration was not cleared, try these additional steps AFTER the router has finished rebooting.
  5. Unplug the router's power.
  6. Press and hold the reset button. While the button is held down, reconnect router's power.
  7. Continue to hold the reset button for 20 seconds after reconnecting the power.
  8. Wait for the router to reboot.
  9. Log in with the default password.
For DGN2000 / DG834Gv5 Routers
To restore the factory default configuration settings when you do not know the login password or IP address, press both the Wireless button and WPS button on the side of the modem router for 5 seconds.
For FR314, FR318, and FV318
These routers require reloading the firmware in order to recover from a lost password. Download the most recent firmware from NETGEAR's Web site before proceeding. Follow the instructions in the manual.
For routers with a 9-pin manager port on the rear panel: RT314, RT311, RM356, RT328, RT338, RH340, and RH348
See Updating Router Firmware That Uses a Manager Port.

Here is a small video that shows you how:

http://kbserver.netgear.com/media/flash/training/Troubleshooting/NG_WGR614V9Router_TS_LostPassword.html

Good luck.

Mar 10, 2011 | NetGear WNA1100 Wireless-N 150 USB Adapter...

1 Answer

I have a westell versalink 327w wireless router and i need the hard ware to install it where do i get it at.


You do NOT need hardware to install the versalink other than an ethernet cord and the phone cord. By default, you can also use the wireless antenna. The default WEP key and SSID are located on a sticker on the bottom of the DSL gateway.

The ONLY reason to need the software cd is if your ISP has installed a redirect page. There are two ways to disable it- one go through the activation page, or two: in your browser address bar type 192.168.1.1/*insert name of ISP, like verizon*/redirect.htm
It should ask you for the user name and password- by default it is admin and password. You should see a page that has something along the lines of "Select button to disable"- press it, then the modem goes into it's setup pages. No tools necessary. No CD necessary. The only time you NEED the CD is if you are trying to connect via USB- I do not recommend this, since not only is ethernet more reliable, it's faster and does not require an unstable driver added onto your system.

Also, since I suspect you are a Verizon customer (they are the ones that supply the 327w for the majority- Contact Verizon technical support. For the business side it's 888 649 9500, option tech support. They can walk you through setting up your modem as well as send a cd for the modem *if you need to use the modem via USB*

Sep 23, 2010 | Gateway Network & Wireless Adapters

1 Answer

I installed my NetGear wireless USB adapter and the install went fine. It connected to my wireless modem/router that was provided by the ISP. The adapter recognized the network and had an excellent...


I would suspect either a bad password, some additional security settings on the router (like MAC filtering), or perhaps the DHCP server functionality not turned on in the router.
If you have an administrator password to the router, you can check it yourself, otherwise you have to contact the ISP for assistance in router setup.

Sep 08, 2010 | NetGear WG111 802.11g/b Wireless Adapter

1 Answer

I have Dlink WBR 1310 Router which I had set up but now after up grading my laptop I cannot get the set up done and Router is not provided by the ISP I do not remeber my ISP ID/PW and router setup wizard...


Did you try to reset the router ? Once you reset the router, you will lose all the settings of the router and you can set up the router from the scratch.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for step by step by instructions

May 19, 2010 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

I don't have the disc to set it up


Are you trying to set up router ?
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Mar 12, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

How do i connect my verizon dsl westell 6100 to my belkin g rtr?


Wellll....since it seemed an impossible task, I tried the next best thing.
I bought a wireless adapter for the other pc and voila! they are on the internet, and I am returning the router.

Westell modem + Verizon DSL w/usb = No connection to router.

Dec 28, 2009 | Belkin Wireless G Plus MIMO (F5D9010)

1 Answer

Cant connect wireless


HI! I bliv u are having some issue setting up ur router.. I will be more than glad to assist u. here are the steps u need to do:
1. press the reset button on the back of the router for 20sec..while pressing the reset button, unplug the power plug and after 2secs while pressing the reset button plug it back in and press for 30secs after that unplug the router for 15secs then plug it back in..once all the lights are solid and ok
2. connect the ethernet cable to port1 of the router and the other end to the lan port of your computer..
3. pull up ur browser then type at the url:192.168.1.1.or 192.168.0.1 or u can check the routers default gateway by right clicking the network icon on the lower right of your task bar and click on status and it will show the ip address of the computer, subnetmask and default gateway, the default gateway is the routers ip address, once u type in to the url, it will ask u the username and password, by default the username is admin and the password is 1234 or just leave it blank
4. it will show the setup page of the router. u can set the router on the specific internet setup that u have.
a. if ur isp is a cable company, normaly u need to do a mac clone on the router setup page by cloning the computer that is reg to the cable company, how to determine it. ex. the computer that is reg to the cable company is a desktop or laptop, if this computer is connected to the modem directly and u can access internet.
b. once u determined it u need to connect this computer directly to the router and do a mac clone and set ur internet settings to auto-dhcp..then save the settings and after that, unplug to the power of the modem and router, plug in 1st the power of the modem then once all lights lit, plug in the router, then once all lights lit, try to pull up a browser that ur computer is connected directly to the router.. ur cable connection shud be, cable from the modem will go to the WAN port of the router and connect ethernet cable on port1 going to the lan port of the computer..once u can access the internet, u can now access again the setup page of the router by typing at the url:192.168.1.1 and u can setup the wireless settings, u need to create a ssid or wireless name and a security..
5. If ur isp is a dsl normaly they give u a username and password to connect to the internet, ur settings on the router should be PPPoe
6. If ur isp gives u a static ip address settings, u need to set the router to isp setup.
a. how to check the isp of the isp given to u..
1. click on start
2. run
3. type cmd
4. it will show a dos prompt
5. from the dos prompt type ipconfig/all
6. it will list the ip address, subnet, default gateway, dns server
this settings should be type in to the settings on the router for static ip addressing..

if you have any querry pls feel free to get in touch.. good luck


Aug 24, 2009 | D-Link Network & Wireless Adapters

2 Answers

I have a dlink router and I want to connect my usb modem to it


is this an additional router?

Verizon are issuing modem with built in wired and wireless modem.

Try this;
How do I properly set up a D-Link Router with a Westell Modem? (#7125)
This FAQ is for setting up a BellSouth supplied Westell 2100/2200/6100 modem (Models A90-210030-04, B90-220030-04 and B90-610030-06/C90-610030-06, respectively) with a D-Link DSL router. Although actual screen shots vary throughout the DLink line, the instructions below are applicable to all models. Important Note: These procedures and pictures are based on the most recent firmware for the Westell. Other Westell firmware menus and screenshots are slightly different but the bridge options and functions are still available. It is highly recommended that you click here and update your Westell firmware.

This FAQ has 3 Major sections:
Section 1 - Overview
Section 2 - Westell modem configuration
Section 3 - D-Link router configuration information
Section 4 - Connections and power up

Section 1 - Overview
bred.gifImportant Note: Due to some known operational issues it is VERY important that you have the latest firmware on your D-Link router. Please go to the D-Link Support Site for firmware updates.
bred.gif The best configuration for networking a router with the Westell is to set the Westell to "Bridged Ethernet" mode and allow the router to do the routing and DHCP functions. The Westell is also a router with full DHCP functions and may not function correctly when connected directly to another router. Not changing the modem to Bridged Ethernet will result in double NAT'ing, increased latency, possible IP conflicts, or possibly a network that doesn't work at all.
bred.gif Before proceeding both the modem and router should be set to default. Despite what the help desk tech tells you, resetting the Westell does not put it into Bridged Mode.
bred.gif The BellSouth Installation CD and Connection Manager are not required to use this configuration.
bred.gif Since BellSouth assigns static WAN IPs via your username the configurations shown are applicable to both dynamic and single static IP customers. Select dynamic PPPoE regardless of your setup.
bred.gif You must connect the Westell directly to the computer's NIC to make the necessary changes before you connect the router, because you will be unable to access the modem interface after you connect the router. The reason is that the modem interface is 192.168.1.254 which is a local IP. By default, most routers do not have the capability to route a local IP out of their WAN port (where your Westell is connected). Additionally, they may be on completely different subnets. After you have made the changes to the Westell you can then connect the router and configure it for use with FastAccess. There are several alternatives around this problem. One method involves extra equipment (second NIC and a hub) and major configuration changes. The second method requires you to utilize the router as a simple switch and use the Westell's PPPoE and DHCP functions. Click here for more information.
bred.gif If you encounter any problems simply reset the Westell, connect it directly to your NIC, restart your computer, log into the Westell interface, and start over again.
bred.gif More information about the Westell is available here.

Section 2 - Westell Configuration
bred.gifStep 1
Verify that your NIC card is set to "Obtain IP Address Automatically". Completely power down the Westell and the computer(s). Power up the modem and press the reset button on the back of the modem. After the modem has fully initialized connect the Westell to the NIC and then power up the computer.

bred.gifStep 2
Open a browser session and enter 192.168.1.254 in the URL address field to access the Westell interface. If you are unable to access the interface make sure your NIC is set to "Obtain an IP address automatically". This may require you to reboot the computer (or release/renew) to obtain a proper IP.

bred.gifStep 3
Click on Broadband DSL Line from the top menu. Click on Configure Connection from the right menu. Select "Bridged Ethernet" from the Protocol pull down. Click on Save and restart the connection at the bottom. This will automatically restart the modem and the interface will return after the changes are saved. Note: functions like NAT, DHCP, IP Passthrough, and username and password will be disabled or irrelevant and can not be selected. After the modem has restarted, power down both the computer and the modem then physically disconnect the Westell.

Section 3 - D-Link Router Information
bred.gifStep 4
After the PC is powered down connect one of the router LAN ports to the computer NIC and power up the router and then the computer.

bred.gifStep 5
Use the following steps to configure your D-Link DI-604 Router. Important Note: You must use the username@bellsouth.net format for your username. If you do not add "@bellsouth.net" after your username you will be unable to connect to the internet.
image92920.gif
image92921.gif
image92922.gif

Section 4 - Connections and Power Up
bred.gifStep 6
Power everything down and physically connect the Westell, the router, and any computer(s).

image78985.gif
Westell 2100 shown. Pictures by Andy Houtz

bred.gifStep 7
Power up the network equipment in this order:
•Westell Modem (wait till the Ready light is a steady green)
•D-Link Router
•Computer(s)
Open a browser session and go surfing!

bred.gifAdditional Imformation
•You should check your tweak settings to optimize your new network. Reminder: If you are required to change your MTU, make sure that it is identical on all equipment (PCs and routers) in the network. For more information about changing MTU on a D-Link please click here.
•The 6100 has an "Internet" light that is green whenever there is an active PPPoE session initiated by the Westell. Since you are using the DLink to establish the PPPoE session the light will stay off. This is normal.


Mar 13, 2009 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

Rest password on DNA-A211-I ADSL2+ Modem


hi..
the only way to restore the router is to hard reset the router,which will reset the router to the factory defaults and then setup the router as the first time installation and the default username and password will be restored,i kno this is much of a work to reset the router and again setup the router like 1st time installation but this is the only way to retrieve the default user name and password..

vedhick

Jan 15, 2009 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

DSL modem and Linksys Wireless Router not working together anymore


if i were to guess you are probably a PPPoE user with a dynamic IP address.

possible config

Dec 18, 2007 | Network & Wireless Adapters

Not finding what you are looking for?
D-Link 802.11g Wireless Router WBR-1310 (WBR1310) Logo

Related Topics:

1,172 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Network & Wireless Adapters Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Mike McWhinney

Level 3 Expert

537 Answers

Cosma Papouis
Cosma Papouis

Level 3 Expert

404 Answers

Are you a D-Link Network and Wireless Adapter Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...