Question about Projection Televisions

1 Answer

Freeview box model CG5660-M remote does not work the set top box and buttons on the set top box do not work either

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Depending on how long you have had it you can get a refund or replacement cos my remote broke and now i cant tune in my channels after turning it off at the plug.

Posted on Apr 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want an instruction manual for an Hitachi HDR505 set top box


My Hitachi freeview + recorder hdr505 keeps freezing when i go to tv guild to set to record programs

Mar 31, 2012 | Projection Televisions

1 Answer

Can you tell me how to tune in a channel when ppreparing to use a freeview box on a onyx sw 1536 ld


Unless you've got an "expensive" Freeview box that modulates its output on to the RF (Aerial) connector then you can't. Most Freeview boxes have 2 aerial connectors - 1 IN from the Aerial itself and 1 OUT to connect to the TV - BUT this is ONLY a PASS-THROUGH connection. This means that the digital Freeview signal which is decoded from the aerial signals is NOT output on the OUT connector and sent down the co-axial cable to your TV. Only the "old" ANALOGUE (not Freeview NON DIGITAL) comes down that co-ax. What you should do is connect the Freeview box to your TV with a SCART cable via the SCART connectors on both. You need to select the AV input on the TV using the remote.
Even if you do have an "expensive" box that does modulate the digital decoded programmes and output these of the RF OUT connector, you should still use a SCART cable as the picture produced will be far better
Hope this helps

Jul 06, 2010 | Projection Televisions

1 Answer

How do i get the red light that says LOCK, off, on my Digital set top box ? (CG5660-M)


hello Enter the Supper password "1998" when the screen appear "Enter unlock Code"

If super password failed to work pls do as follows:-
(a) press "Standby" button on the remote contorl, then unplug the power cord (within 2 sec.) of the set top box IMMEDIATELY;
(b) After 3 sec. plug in the power cord to the STB again;
(c) Repeat step (a) & (b) until the STB enter the "First Time Installation" screen. Then the box will proceed channel search again.

regards
shaun

Feb 27, 2010 | Projection Televisions

1 Answer

Only goes from red to amber on led


it was to do with a faulty freeview box replaced it everything now works tv was not at fault

Jun 17, 2009 | Sony Grand WEGA KF-42SX300 42" LCD TV

1 Answer

Cant retune my digtal freeview as my picture keeps freezing


The retuning process is as follows:

  1. Press the [i+] or MENU button on the remote control to display the DIGITAL INFO menu.
  2. Press the BLUE button to display the MAIN MENU.
  3. Press the UP or DOWN buttons to highlight AUTO TUNING then press the OK button to display the AUTO TUNING MENU.
  4. Press the RED button to start the auto tuning process for all available digital channels.
  5. Wait for the process to complete.

If you wish to CANCEL the auto tuning process whilst it is processing then press the BLUE button at any time.

You may lose some channels when you retune the TV as the channels have been rearranged. To locate them look at the EPG although you may still find that some channels are no longer available on FREEVIEW. See the following link for additional information

http://www.freeview.co.uk/_retuneinfo/

If the above process does not work then check the link above for additional information and also visit the accompanying site links below to find more information for your model of TV / FREEVIEW box.

For troubleshooting the retune procedure visit http://tvretune.co.uk/troubleshooting/

For specific model information visit http://tvretune.co.uk/productmanuals/

Jun 02, 2009 | Samsung HL-S5086W 50" HDTV

1 Answer

I need a remote control code for my nikkai a88jb freeview box so that I can programme a universal remote control. Any ideas?


my nikkai a88jb after connected still come up with "empty data base" . no signal of anything showing and i did plug in antenas! pls what shoul i do?

Apr 18, 2009 | Projection Televisions

2 Answers

I have an Onn 15'' LCD TV Model No OLCD1504 and am trying to connect a DVD player that only has an AV out.I have tried connecting it with a Scart to Av lead in all combinations i.e. via freeview box,direct...


Some dvd players do not have the switching line fro your tv to automatically select scart input but you will be able to select via the tv remote if there are no buttons marked av it can be an oblong with an arrow pointing inwards or you may have to select via the source menu on the tv if you have your original handbook it will give a helpline number for Asda.SUPER8.

Jul 31, 2008 | Projection Televisions

2 Answers

Do not understand how to set up my alba digi box to my television and recieve basic digital channels help!


Hi.

Ok
1) plug aerial in to the antena in sock on freeview box.
2) plug short aerial type lead in to rf out socket on freeview & antena in socket on TV.
3) plug A scart lead in to the socket marked TV on freeview box & the other end of scart in to one of the scart sockets on the TV.
If your TV has more than one socket plug it into the one marked AV1 or AV2.

4) plug in freeview to mains electricity & switch box on.
5) Turn TV on freeview should appear automatically if it doesnt look on your TV remote for A button marked AV or a button with either A circle or square with an arrow going through it you may need to press this several times until you see digi picture come up.
Thats basically it but do check that you dont need a new aerial etc to be able to get digi signal in your area.

http://dysonmanuals.llc.nu/

Jul 26, 2008 | Projection Televisions

1 Answer

Hi I'm trying in install Freeview but it doesn';t work. Do I need to have the TV on AV?


Hi.

If your freeview box is not built in to to TV set & it is a seperate stand alone box it must be connected to the TV using scart lead.
Then press AV on tv remote if it doesnt automatically show on TV screen.

http://dysonmanuals.llc.nu/

Chris.

Mar 07, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...