Question about Philips 42PF7320A 42 in. Plasma HDTV

1 Answer

Bottom half of screen isblack

Where can I get a buffer board?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 52 Answers

Part distributors for philips are http://www.andrewselectronics.com./ and http://www.vancebaldwin.com/. hope this helps

Posted on Aug 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My screen went black


If the bottom is black it's the lower buffer board and I believe that's the Y buffer board. Should have on ebay fairly inexpensive

Aug 11, 2014 | Philips 50PF9631D 50 in. HD-Ready Plasma...

1 Answer

Lg plasma DT50py10. When turning on bottom half of screen is snowy and has lots of white lines for approx 20 min then it goes away. Top half of screen is normal


sounds like your bottom buffer board is on its way out .
Will also need to check the y sus board as this some times causes the buffers boards to fail.

May 24, 2011 | LG DU-50PX10 50 in. Plasma HDTV

1 Answer

Hitachi 50" hd TV displaying black lines on screen


Sounds like your YBL-Y Buffer lower board is going out. There are 3 boards here. The Y buffer upper which controls the top half of the display, The Y buffer lower controls the bottom half and the Y-SUS main control those two boards. They work in unison. Usually if one goes out you have to replace all. You can also get lucky and just repalce the YBL and all may be well. Now if they are vertical lines up and down the OSD-On screen display, then this is indicitive on dry solder joints on the D, G E, F boards. Hope this helps...

Jun 29, 2010 | Hitachi P50H401 50 in. Plasma HDTV

1 Answer

My 5 years old Plasma TV found half of the screen picture view not very clear.. The half colour seen blur..


Your Buffer boards or the YSUS main are bad. THe YBU-Y Buffer upper controls the top half of display, the YBL-Y Buffer lower controls the bottom half and the YSUS Main controls both those boards. They are located to the Far Left on and opened Set.

Jun 21, 2010 | Philips 42PF9966 42 in. HD-Ready Plasma...

3 Answers

Black screen


first try the address board or buffer board.if this
does not repair it,the panel is defective.

Jul 17, 2009 | LG 42PC3D 42 in. Plasma Television

1 Answer

Phillips 42 inch Plasma -Screen Issues!!!


intermittent loss of picture on either bottom or top half of screen is specific to y buffer boards located on left side of screen going from top to bottom when looking at back of tv. the y lower buffer would be the board to replace to resolve the loss of bottom half of picture. if the top half also is going out intermittently could tied to upper buffer as well but just a note the y main board to right of these buffers drives those two boards so in some cases could also be part of the problem. if only bottom half is affected i would recommend replacing lower buffer only

Aug 07, 2008 | Philips 42PF7320A 42 in. Plasma HDTV

1 Answer

Model 42mf231d/17 42" plasma


If the loss of picture is either on top half or bottom half of screen. there are y buffer boards that go from top to bottom on left side of screen when looking at back that control those sections. when there is loss of half of picture then buffer associated with that area would be at fault and would need to be replaced. when i see a degrading symptom such as loss of picture on top half or bottom half leading to no picture issue normally you would check heat syncs on y sustain board and if not heating up after a few minutes of being turned on would recommend replacing y main and both y upper and lower y buffer boards as they complete a circuit

Jun 04, 2008 | Philips Magnavox 27MS343S 27" TV

1 Answer

Half screen activated only


When only a half screen is produced, it is usually a upper or lower buffer board, if the top half is blank then it is the upper buffer, and of course if it's the bottom half then it's the bottom buffer board

Sep 15, 2006 | Panasonic TH-42XVS30U 42 in. Plasma HDTV

Not finding what you are looking for?
Philips 42PF7320A 42 in. Plasma HDTV Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72230 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...