Question about Dishwashers

1 Answer

Dishwasher blew electrics ,turned fuses back on then dishwasher did not finish washing and emptying cycle

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

I would require more info before offering a solution. Please provide make/model of machine.

Posted on Aug 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asko dishwasher did not finish complete washing cycle and now has a very low humming sound. It will not start washing cycle. I have turned it on and off but after I turn it back on humming sound...


Some wash water may have gotten into the bottom pan area below the wash tub. If water has overflowed from the tub into the bottom pan, the drain pump will activate and remain active until water has been removed from the bottom pan. To check for this, the lower front panels will need to be removed. With power turned off at the breaker, a wet-vac can be used to remove water from the bottom pan. If there was water there, check the door seals, door closure and make sure the drain hose has a high-drain loop. If the drain is shared with the kitchen sink, it may simply have backed up into the dishwasher through the drain hose when a full sink was emptied. The best drain system is for the dishwasher to have its own separate drain.

Jun 29, 2011 | Asko Dishwashers

2 Answers

Hotpoint Dishwasher BF1620 blew the main fuse circuit in fuse box during mid cycle wash? Re-set main power fuse circuit but now as soon as Dishwasher switched on immediately blows main kitchen power fuse...


This is happening because you have a very bad fault, a Phase to Earth short, problem. Leave machine UNPLUGGED, Breaker/Fuses OUT. do NOT use it, nor Touch it, It is possible to get severe electric shock. PLEASE get a registered serviceman to inspect this unit.

Feb 07, 2010 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

I have a Bosch Exxcel 1400 S Express which blew


There is no internal fuse in the washer to replace.
If you have replaced the fuse, make sure that is is a good one.
If you are satisfied that you have power to the washer, then I'm afraid it sounds quite serious.
Trust this helps.

Dec 04, 2009 | Bosch Washing Machines

1 Answer

When selecting a wash programmne, dishwasher


sounds like the program board has failed . try shutting off the power ( at the fuse box ) for 15 min then turn it back on. this will reboot your system and if the board is not bad it will wor properly ..

Nov 22, 2009 | Dishwashers

1 Answer

Water standing in bottom of dishwasher,after wash cycle is finished? This is a Kenmore model 665.1565591


My problem too recently.

I blew compressed air back through the drain line and let it bubble up in the standing water in the dishwasher. Then I put it through another cycle and everything was fine. Something must have gotten clogged and the air blew it out.

Mar 19, 2009 | Kenmore Dishwashers

1 Answer

Kenmore Ultra wash ll


sounds as if you may have blowna fuse on the control board, i would check incoming ower supply first for 110v. if power supply is good i would reomve the panel and check the circuit board for a a fuse that might have blown little white fuse attached to the side of the electronic control

Nov 08, 2008 | Kenmore 15129 Built-in Dishwasher

1 Answer

Meile G638 I Plus dishwasher


Problem solved, the dishwasher starts its wash cycle with a drain sequence, the pan did not drain in time for the wash cycle to continue , thererfor locking it out on inlet/drain alarm. I removed the drain hose from the S trap, then the non-return valve from the filter basket, made sure the drain pump impelar was free, blew down the drain hose back into dishwasher to clear any waste in the pipe,then found a block in the S trap orifis, after clearing that, reasembled and test run on cold pre wash cycle this runs for aprox 10 min.customer was very happy.

Mar 30, 2008 | Dishwashers

1 Answer

The fuse in the plug keeps blowing. Initially it would run for a while - sometimes 3 or 4 cycles - before blowing. It now blows the fuse the second that I plug in to the socket, even with the on/off button...


Lower the outlet hose into a washing up bowl, it should then Drain. Check the heater to see if it is earthing you get to it by removing the right hand side panel.

Nov 28, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15220 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...