Question about Washing Machines

1 Answer

Maytag MAH2400 circuit board failure 2nd time in less than 1 year

Posted by on

  • gunner417 Dec 11, 2008

    would like to know the same as scott. same problem here, haven't replaced the board yet though. could it be the pressure sensor??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi the problem you had with the drain pump that cycles and the motor that would not spin what was the fix the board or the motor. thanks scott 512-784-3874

Posted on Oct 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New whirlppol frontload. less then 6 mos & broken 4 the 2nd time. they say its computor board. do u know if this is a prob w/ them?


The problem with the computor board, the CCU (it's actually just a simple circuit board) is that there are cold solder joints where the relays and the spade connectors connect to the circuit board. Have those cold solder joints touched-up and you should be ready to go.

Oct 18, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The door on my Maytag MAH2400 will not unlock. I have tried shutting off power to no avail. There is a throw rug in the washer that looks like it is caught in the door. Is there a manual release that...


Sorry no theres not,And when you get the throw rug out do not put these in there they do a lot of damage they can clog the pump.First thing try pushing the start button agin you well have to do this several times the machine has to drain before the door opens,when it open up.put draino-max and let it stand for 1-2hrs and run machine no clothes.And no more throw rugs

Jul 04, 2010 | Maytag MAH2400A Front Load Washer

1 Answer

Maytag mah5500bww motor/control board failure recall


I had Maytag ship a new motor and motor control board for free and installed it myself in less than an hour. There is a ten year warranty on those parts. You just have to be very firm and insist you have warranty rights by law!

Feb 10, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Brother 5250dn and all light are blinking


That series of lights indicates a main circuit board failure. You will need a shop to replace the main logic PCB. Could be caused by anything, static shock, bad input power from power strip or power failure, just plain CPU failure. If it's under warranty, 1 year since purchase, you need a Brother service center, out of warranty a new printer would cost less than repair.

Feb 02, 2010 | Brother HL 5250DN Laser Printer

1 Answer

Display goes out-light stays on


Could be a loose connection inside or a circuit board problem, most likely the latter...Bernina Artista machines seem to have greater numbers of circuit board failures to me. Static discharge can fry it in a second.

Aug 17, 2009 | Bernina Artista 180

1 Answer

I have a Maytag Neptune Washing Machine (Front Loader) Part No. 6 2704440 Model # MAH3000AWW Serial # 25103319UF 1st. - on the inside of the washing machine, between the door and the tub, if you will,...


Main bearing failure that led to motor controller/timer failure.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jul 10, 2009 | Maytag Washing Machines

1 Answer

HE5 frontload washer error f11


F11 error code indicates a communication problem. The communication between the Central control board and the Motor control board cannot be sent correctly.

Potential causes:

1. Loose connections between the motor control board and the machine control board, or at
motor

2. Machine control board failure

3. Motor control board failure

4. Motor failure

5. Door lock failure
If this answers your problem, please rate my answer.
Thanks,
David

May 27, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

My daughter has a Bottom Freezer Maytag fridge. Model# PBF2253HEW , Serial # 11366421GR. She has had the refrigerator replaced ounce while under the 1 year warranty due to defrost problems that were not...


cannot usually be done to trigger defrost. best you can do is to try to trace which edge connector goes to heater and with everything disconnected, apply mains to the edge connector

Sep 25, 2008 | Maytag Refrigerators

2 Answers

Control panel lighs blink and ice door opens and shuts. The fridge and freezer is still cold. I called Maytag and they are sending me a new circuit board. The local Maytag store owner told me to...


i just called Maytag (now Whirlpool) @1-800-253-1301.  They are shipping me a free control panel and are also paying for a certified installer to come to my home to do the exchange.  
I told them when I called that I learned from the internet that it was a quality issue and they did not disagree.  They processed the order and offered the installation without me asking.  
My refrigerator is out of warranty so they covered it as a quality issue.  We enjoy our refrigerator and have not had any other problems accept when we first received it and someone had to come and adjust the icemaker.  Yes the icemaker is small by some standards but it meets our needs. When we need lots of ice, for guests we just buy a bag for less than a buck.  
Great service response from Maytag.  Thanks.  

Aug 01, 2008 | Maytag MFI2568AES Stainless Steel Bottom...

3 Answers

Problem with Maytag MAH2400 AWW


As for the user whose machine will not drain and sounds as though a chain is clanking, the solution is probably a coin caught in the drain pump. I just had the same problem. Access the pump from the bottom of the machine. 4 screws hold the mounting bracket on undo those, the electrical connection and two hose to the pump. Undo three screws holding impeller to motor and coin can fall out. Examine for damage if it is not too tore up, put back together. Keep in mind that when you unclamp the hoses that water will come out.

Dec 28, 2007 | Maytag MAH2400A Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Brad Brown

Level 3 Expert

15133 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...