Question about Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

1 Answer

Keyless chuck question

My old Dewalt DW953 12 volt cordless drill has a double sleeve chuck. The current DC727 model has a SINGLE sleeve chuck. What are the pros and cons (if any) to the two chuck designs? Thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 313 Answers

This 2 chuck are 3/8 jaw opening,double sleeve u can hold the chuck will opening it at the sametime.the sinlge sleeve u have to runs the drill while running slow rev/for to remove the bit etc.
i prefer metal sleeve.

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to change keyless chuck


If your wanting the sleeve, #12 on breakdown, then search the part # as There are other places that still have it. http://www.ereplacementparts.com/dewalt-dw056-type-18v-cordless-impact-driver-parts-c-1009_9591_2845.html

Nov 22, 2013 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

How do i insert bit in cordless dewalt keyless hex chuck?


It only accepts 1/4" hex shank bits and nut drivers. Mine just pops in and to release it, you push the black collar around the bit down. Cannot put round end bits in it. Only hex shanks

Oct 26, 2013 | Dewalt DW056 18 Volt Cordless Impact...

2 Answers

How can I replace the keyless chuck on my Dewalt DWD215G?


Open the chuck wide open. In the center is a retaining screw, they usually have left hand threads. Remove the screw. Take an allen wrench1/4" to 3/8" in size and fasten the short side tightly in the chuck. The chucks are usually right hand thread, so take a small hammer and strike the allen wrench to turn the chuck to the left to loosen it. Once you have the chuck off, verify the thread size of the drill motor shaft, then go to McMaster-Carr and choose the one you need.

Apr 16, 2011 | Dewalt DWD215G 12Inch 10AMP Heavy Duty Mid...

1 Answer

Cannot get the chuck to release the bit it is a dewalt and yes I am in reverse


On some of the DeWalt drills I have owned with keyless chucks, the chuck has a locking mechanism.
You have to grip the chuck and slide the outer sleeve forward to release the lock, then you can tighten or loosen the chuck.

Apr 14, 2011 | Drills & Drill/Drivers

1 Answer

How can I disassemble a Dewalt keyless cordless drill chuck? I mean take it apart, not just remove it.


depending on the chuck it would take special fixtures to press apart, and unless you are very good with tools you would damage it beyond repair. I have never taken a keyless apart and tried to repair and put together, I have on the other hand done the same with the keyed chucks.

Dec 13, 2009 | Dewalt Drills & Drill/Drivers

1 Answer

3/8 Drill Driver, chuck replacement.


hi friend,
Step 1. Determine what kind of replacement drill chuck you want - a keyed chuck or key less chuck. Over the years, key less chucks have been widely used for handheld power tool drills, due to their improving grip torque and convenience.

Step 2. If you prefer replacement key less chucks, then you have to know what type of key less chuck you will need - a single sleeve key less chuck or a double-sleeve chuck. You can simply determine it by checking your current chuck. If your current chuck is a keyed chuck or a double sleeve chuck, then you will need a replacement double-sleeve key less chuck. On the other hand, if your current chuck is a single sleeve chuck, then you should get a replacement single sleeve chuck.

drill-chuck-sleeve-type.jpg

Step 3. Confirm the threaded mount size (spindle size) on the chuck. 3/8"-24 threaded mount for 3/8" capacity drill chucks and 1/2"-20 threaded mount for 1/2" capacity drill chucks, but there are some exceptions where just the opposite may occur. To be safe, always check the threaded mount before you buy replacement drill chucks.

drill-chuck-thread-mount.jpg
hope this helps u
please rate me.........................
thank u for using fixya
regards
sivaranjini

Nov 26, 2009 | Craftsman 19.2V C3 DRILL/DRIVER

1 Answer

Cordless Drill, Keyless Chuck stuck in full open position.


if chuck is wide open ,look down inside there should be an allen screw or bolt at the bottom of the chuck it should undo anti clocwise and the chuck comes off

Aug 18, 2009 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

I HAVE A DEWALT DC729 18V DRILL


is this a north american model.all i can find is model DC727 & DC728 model. charger model 9116 & battery is DC9096 may work.charger volts 110v ac. if your buying the individual part like batt & chgr its more expensive than buying the whole kit is cheaper. hope i answer your question

Jun 20, 2008 | Dewalt 18 Volt Compact Drill Kit

1 Answer

Drill chuck swap


1. Turn the screw clockwise to take it out.
2. Then you needs 3/8 allen key & insert the short side of the allen key & tighten the chuck.
3. hold the drill at the edge of the table & wack the allen key
counter clockwise & do it again as needed.
4. dewalt keyless chuck will fit but you might add a washer to insure the chuck is not rubbing the clutch collar.
5. putting it back together the other way.

Jun 01, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

2 Answers

Never have used a keyless chuck b4- need to change bit, how do I do this? thanks


hi this should be reletively easy hold the end black bit with the sivler bit holde coming out not the black bit next to the yellow case on drill you hold the black part thats at end of drill by where the bit goes into not the black bit near the trigger hope i explain this ok.
Hold this bit tight then put drill in reverse then press trigger a couple of times it might be tight but shouldnt be that tight it wont undo.
1 put in reverse
2 hold black plastic piece near where drill bit goes into
3 press trigger few times
4 this should undo it allowing you to put a bit in
make sure its in reverse else you will just tighten it up more let me know if you need further assistance ok

Mar 05, 2008 | Dewalt 18 Volt Compact Drill Kit

Not finding what you are looking for?
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills & Drill/Drivers Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Jim Thurston

Level 3 Expert

669 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Are you a Dewalt Drill and Drill/Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...