Question about Harley Davidson Harley-Davidson Motorcycle Desktop Telephone

1 Answer

Radio & horn 04 Road Glide

I put new handlebars on my 04 Road Glide and a friend did the dis & reconnect of the wiring. everything looks ok, but now my radio & horn don't work. Are the horn and radio on the same circuit, is there a fuse and where would I find it.

Thanks
Jonn

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,028 Answers

Generally these aren't on the same circuit. There is an inline fuse for the radio, it's located in the power wire for the radio. The horn shouldn't have a fuse, so I'm going to say check the button on the controls.

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Phone line is busy, but the cordless phone is hung up


If the line is busy, there's a phone off the hook somewhere or there's a bad phone jack or line cord. If this is the only phone on the line, disconnect the AC power adapter from the base and also disconnect the battery in the handset. On both units, press a couple of buttons to drain off stored charge. After a minute or so, reconnect the battery and base power, and see if the line is free. Sometimes, especially in hot weather when lots of people using air conditioners or storms can cause power line glitches, the computer in the phone gets confused. This process resets everything and may clear up the trouble.

If you don't have another phone and the trouble continues after trying the reset, see if you can borrow another phone from someone for testing. If that fixes the trouble you need a new phone.

Your phone line itself might have a problem that is causing your phone service provider to think your line is in use. There may be water in the line or some other fault outside, or some problem on your inside wiring. (A friend had a problem after she plugged in a new phone, and it turned out one of the prongs in the jack had bent and was touching the one next to it. In another case, a phone jack that had gotten wet had corroded and was shorted.)

If you have other phones on the line, disconnect them all from their jacks. Reconnect one and see if the line is free. Then you can reconnect the others, checking each time. This will let you determine which one is causing the problem.

This kind of problem can be frustrating, but it can be solved. Good luck, and thanks for using Fixya!

Aug 03, 2011 | Vtech 5867 Cordless Phone

9 Answers

Samsung champ gt-c3303 unlocking code


You need Network Unlock code?or else Security Unlock ?
Security Unlock code can be get from the service provider and Network Unlock code can be get from Unlocking websites,you can get the Unlock code from here
Superunlockcodes at low cost and get the Free Unlocking instructions from here
Mobileunlockguide

Jul 08, 2011 | Samsung Phones

1 Answer

Horn does not work on my 1999 harley davidson Fat By motorcycle


First check the two wires going to the rear of the Horn. One ground One Power. If they are connected to the horn then check the ground wire it comes lose most often. If you have power to the Horn then the Horn is defective. If you have no power to the horn it is necessary to trace up to your switch houseing. Usually the problem is ground, I have found defective horns but not often. You can take the horn off and using a battery and wire touch the two prongs in the back of the horn.If it works then the problem is either ground or power. Make sure horn is grounded. Usually the problem is a grounding one. Good Luck.

Mar 13, 2010 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

Head lamps


On the left handlebar the beam switch has an input wire and 2 outputs. The yellow output is low beam and the white is high. The wiring harness exits the switch housing and resides in a dimple on the bottom side of the handlebar. This is a very easy place to pinch a wire. Have you replaced grips or installed chrome switch housings? Yank the connectors off the headlights and try it again. If you have a broken filament that is touching the other filament it will draw way too much current, and if it doesn't kick with the lights unplugged then one or the beams is bad. One other thing that is rare: I have seen a failed dimmer switch turn on high and low beam at the same time. Temporarily install a higher amperage fuse that won't blow and look at the filaments through a welding hood to see if they are both on. Do this last.

Oct 06, 2008 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

FXRS CONV -INSTALL TRIPLE TREES TO MAKE A WIDE GLIDE FRONT END


As long as the triple clamp stem is the same diameter, the triples can be changed out. As far as why, you're guess is as good as mine. Mine is that some people may like the narrow or mid glide front end, and an 883 just wouldn't look right as a wide glide.

Jul 30, 2008 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

2002 FLTR Radio Problem


Sounds like you may have blown one of the radio fuses. Don't know about that radio but usually there is one fuse red wire for the key hot and one fuse for the radio memory yellow wire and one of em is blown. I don't know if there are security codes for those radios or not if both of the fuses are good. Dont know if it will be a main radio fuse just in the main fusebox or block or if there is another or other fused in the fairing.

Jun 07, 2008 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

Reconnect phone jack wire


Put the blue wire back on the red wire from the jack.

Mar 27, 2008 | NEC Dterm DTP 16D-1 Corded Phone

1 Answer

Phones won't work


A) Ok first try to disconnect everything and connect all the batteries and cable back. Charge your batteries to full. Then if it still Out of range, do this with all your handsets.
- Disconnect the battery
- Hold the * and # key on the Handset and put the battery back without releasing the buttons. (now your in test mode)
- press the 2 softkey below the screen ( it's a factory reset, erase everything)
- You will see RAM/EEprom erase on the screen
-After the bip press end

B) OK! Now disconnect the power adapter from your base unit .
-Hold the memory button on your base and plug the power adapter at the same time. Then the base will bip to let you know that you done it correctly.
-after the bip press No.1 ( that's mean the handset 1 is de-registrer.
- Now De-register all the other handset by doing the part B again. But only changer the No.1 for 2 then 3 then 4.

C) Disconnect and reconnect everything and use your manual to register your handsets with the base and your done! Everything should be ok !

Nov 21, 2007 | Uniden DCT648-3 Cordless Phone

Not finding what you are looking for?
Phones Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Phones Experts

kakima

Level 3 Expert

96372 Answers

Brian Mathews

Level 1 Expert

20 Answers

Brudog1

Level 1 Expert

35 Answers

Are you a Harley Davidson Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...