Question about PC Desktops

1 Answer

I have lost my Mitac E8188 setup disk where can i get one from with xp drivers thank you the duck

Posted by on

  • Anonymous Mar 05, 2009

    Hi,

    Try MICRO NANO IT based in telford they provide repair service for mitac models they should be able to help with drivers.


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Contact Easyrepair.uk they provide back up service to HiGrade. They will direct you to their website which has all the drivers you require. However, should you not have any further use for your Mitac e8188, I would be interested in buying it. I have one which I need to repair and I am looking for a replacement, or spares.

Reagrds

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

INSTALLED ILLEGAL WINDOWS 7 AND WANT TO GET A LEGAL VERSION OF XP BACK


Hope this would be helpful. Kindly follow the instructions.

Prepare the hard disk according to the manufacturer's instructionsIf you are using a SATA hard disk, skip this step and go to the "Determine the type of file system that you want to use" section. If you are using an IDE hard disk, set the jumpers and the cabling according to the role of the hard disk (for example, master or subordinate) and make any required BIOS (or CMOS) changes. To set the jumpers and cabling, and make any required BIOS or CMOS changes, see the documentation that was included with your hard disk and motherboard, or contact the manufacturers.Determine the type of file system that you want to useYou can use either the NTFS or FAT file systems. NTFS is the preferred file system to format the hard disk unless you want to run an earlier version of Windows that cannot read NTFS partitions. For additional information about the differences between the FAT and NTFS file systems, click the following article numbers to view the articles in the Microsoft Knowledge Base: 100108 Overview of FAT, HPFS, and NTFS file systems 310525 Description of the FAT32 file system in Windows XP If the hard disk already contains data, back it upMake sure that you back up all your important data before you continue. When you partition and format a hard disk, all the data on that partition is permanently deleted. You can view current partition information without deleting your data. For additional information about how to use the backup utility or the Files and Settings Transfer Wizard, click the following article numbers to view the articles in the Microsoft Knowledge Base: 320820 How to use the Backup utility to back up files and folders in Windows XP Home Edition 309340 How to use Backup to restore files and folders on your computer in Windows XP 293118 How to use the Files and Settings Transfer Wizard 306186 How to use the Files and Settings Transfer Wizard from CD-ROM 306187 How to use the Files and Settings Transfer Wizard Disk in Windows XP If the hard disk has a drive overlay or a disk management program, make sure that it is compatibleIf your computer uses drive overlay software for large hard disk support, do not use the Windows XP Setup program to partition or to format the drive until you have verified that Windows XP is compatible with the software. If you have drive overlay software installed, contact the software manufacturer to find out whether it is compatible with Windows XP. If you are not sure whether you have drive overlay software installed, contact the manufacturer of your hard disk drive or motherboard.If you have software that you want to reinstall, verify that you have the disksMake sure that you have the original CDs or floppy disks so that you can reinstall the software programs after you partition and format your drive. If you purchased an upgrade for a program, make sure that you have the full version of the original program. Many upgrades for programs require a compliance check before you can install the upgraded product. If you cannot find the original CDs or floppy disks, contact the software manufacturer before you continue.If you have updated device drivers for peripheral devices, back them upIf you have installed an updated device driver for your peripheral devices (for example, modems and printers), make sure that you back up the new driver for the device to a location other than the drive that you want to format and partition so that you can reinstall it after you install your operating system.Configure your computer to start from the CD or DVD drive To start your computer from the Windows XP CD, your computer must be configured to start from the CD or DVD drive. In some cases, you may have to modify your computer's BIOS settings to set this configuration. For information about how to configure your computer to start from the CD or DVD drive, see the documentation that is included with your computer, or contact the computer manufacturer.

If you have a computer that cannot start from the CD or DVD drive and you need to start your computer from the startup disk, make sure that you have the floppy setup disks so that you can run the Setup program from the floppy disk drive.

Note You can obtain Windows XP Setup boot disks from Microsoft, but only by download. We provide the Setup boot disks so that you can run the Setup program on computers that cannot use a bootable CD-ROM. If you can start your computer from a CD-ROM or from a network-based installation, we strongly recommend that you use those installation methods instead. Future products will no longer support installation by using the Setup boot disks.uparrow.gifBack to the topHow to partition and format the hard disk using the Windows XP Setup programYou can use the Windows XP Setup program to partition and format the hard disk. To do this, use the following steps:Step 1: Partition the hard disk
  1. Insert the Windows XP CD into your CD or DVD drive, or insert the first Windows XP Setup disk into the floppy disk drive, and then restart the computer to start the Windows XP Setup program.

    Note If you are using the Windows XP Setup disks, insert each additional disk when you are prompted, and then press ENTER to continue after you insert each disk.
  2. If you are prompted, select any options that are required to start the computer from the CD or DVD drive.
  3. If your hard disk controller requires a third-party original equipment manufacturer (OEM) driver, press F6 to specify the driver. For more information about how to use F6 to supply a third-party OEM device driver while the Windows Setup program is running, click the following article number to view the article in the Microsoft Knowledge Base: 314859 Limited OEM driver support is available with F6 during Windows XP Setup
  4. At the Welcome to Setup page, press ENTER.

    Note If you are using the Setup disks (six bootable disks), the setup prompts you to insert the Windows XP CD.
  5. Press F8 to accept the Windows XP Licensing Agreement.
  6. If an existing Windows XP installation is detected, you are prompted to repair it. To bypass the repair, press ESC.
  7. All existing partitions and non-partitioned spaces are listed for each physical hard disk. Use the ARROW keys to select an existing partition, or create a new partition by selecting the non-partitioned space where you want to create a new partition. You can also press C to create a new partition using non-partitioned space.

    Note If you want to create a partition where one or more partitions already exist, you must first delete the existing partition or partitions, and then create the new partition. You can press D to delete an existing partition, and then press L (or press ENTER, and then press L if it is the System partition) to confirm that you want to delete the partition. Repeat this step for each existing partition that you want to include in the new partition. When all the partitions are deleted, select the remaining non-partitioned space, and then press C to create the new partition.
  8. To create the partition with the maximum size, press ENTER. To specify the partition size, type the size in megabytes (MB) for the new partition, and then press ENTER.
  9. If you want to create additional partitions, repeat steps g. and h.
  10. To format the partition and install Windows XP, go to step 2.

    If you do not want to install Windows XP, press F3 two times to exit the Windows Setup program, and then do not follow the remaining steps in this article.

    To format the partition without installing Windows XP, use a different utility.
Step 2: Format the hard disk and install Windows XP
  1. Use the ARROW keys to select the partition where you want to install Windows XP, and then press ENTER.
  2. Select the format option that you want to use to format the partition. You can select from the following options:
    • Format the partition by using the NTFS file system (Quick)
    • Format the partition by using the FAT file system (Quick)
    • Format the partition by using the NTFS file system
    • Format the partition by using the FAT file system
    • Leave the current file system intact (no changes)
    Notes
    • If the selected partition is a new partition, the option to leave the current file system intact is not available.
    • If the selected partition is larger than 32 gigabytes (GB), the FAT file system option is not available.
    • If the selected partition is larger than 2 GB, the Windows Setup program uses the FAT32 file system (you must press ENTER to confirm).
    • If the partition is smaller than 2 GB, the Windows Setup program uses the FAT16 file system.
    • If you deleted and created a new System partition, but you are installing Windows XP on a different partition, you are prompted to select a file system for both the System and Startup partitions.
  3. Press ENTER.
  4. After the Windows Setup program formats the partition, follow the instructions that appear on the screen to install Windows XP. After the Windows Setup program is finished and you have restarted the computer, you can use the Disk Management tools in Windows XP to create or format more partitions. For additional information about how to use the Windows XP Disk Management tools to partition and format your hard disk, click the following article number to view the article in the Microsoft Knowledge Base: 309000 How to use Disk Management to configure basic disks in Windows XP
uparrow.gifBack to the topAdditional notesBefore you can install an operating system such as Windows XP, you must first create a primary partition on the first physical hard disk (Disk 0) on your computer. Then, you can format a file system on that partition to create what is called the System partition.

Or, you can create a separate partition for the operating system on any physical hard disk. This is known as the Startup partition. The System partition on Disk 0 can also be used as a Startup partition.

Jun 19, 2011 | eMachines EZ1601-01 PC Desktop

2 Answers

I have an ACER Aspire AST160-US321H that does not see the SATA drive anymore. Once the system sees it I need to restore from Disk due to Malware. Does the T160 have a restore from disk option or do I need...


Boot on windows XP when you see the message press F6 to install 3rd party SCSI drivers then hit F6, download a driver for your SATA drive and put it on flashdrive or diskette, After loading setup files the system file explorer pops up to manually locate the driver for your SATA device.

Oct 17, 2009 | PC Desktops

3 Answers

Install XP on SCSI HDD - Instellistation Z Pro 6223-CTO


Have you tried putting the drivers on a flash drive.

It is a method I have used to get drivers into the windows install.
Try it with the "press F6 to install drivers" during the text setup phase but make sure they are the dos level drivers that you try first !

If that fails then try the windows level drivers

Worked quite well on lots of early SATA stuff so you have nothing to loose.
You might also want to check that the various usb settings in bios are set to legacy etc too.

Aug 20, 2009 | PC Desktops

1 Answer

How to install Adaptec SCSI driver when installing XP -Z Pro 6223


you have to use sata xp cd to intall that driver no need floppy disk.

Aug 19, 2009 | IBM IntelliStation Z Pro 6221 PC Desktop

3 Answers

Missing or corrupt hal.dll file, so can't boot the hard drive


Hey,

Please use the recovery discs or windows installation cd.

To either perform a full system restore with the recovery discs.
Or to perform a repair installation with the windows installation cd.

Boot the computer using the XP CD. You may need to change the boot order in the system BIOS so the CD boots before the hard drive. Check your system documentation for steps to access the BIOS and change the boot order.
When you see the "Welcome To Setup" screen, you will see the options below
This portion of the Setup program prepares Microsoft
Windows XP to run on your computer:
To setup Windows XP now, press ENTER.
To repair a Windows XP installation using Recovery Console, press R.
To quit Setup without installing Windows XP, press F3.
Press Enter to start the Windows Setup. do not choose "To repair a Windows XP installation using the Recovery Console, press R", (you Do Not want to load Recovery Console). I repeat, do not choose "To repair a Windows XP installation using the Recovery Console, press R".
Accept the License Agreement and Windows will search for existing Windows installations.
Select the XP installation you want to repair from the list and press R to start the repair. If Repair is not one of the options, END setup.
Setup will copy the necessary files to the hard drive and reboot. Do not press any key to boot from CD when the message appears. Setup will continue as if it were doing a clean install, but your applications and settings will remain intact.

Thanks and good luck.
Ekse

May 03, 2009 | Dell Dimension 3100 PC Desktop

1 Answer

I have a wd sata hard disk and i cant setup windows xp on it, it the monitor says ..... " windows can not find any hard disk instal into your motherboard " i need to solve this problem please thank you


Windows XP didn't have support for sata drives. You will need to load the driver by pressing F6 when you start the Windows setup. You will see the message
Press F6 to load 3rd party drivers at the bottom of the screen when Windows is installing.

Apr 06, 2009 | MSI PC Desktops

3 Answers

I need the software driver for my NEC TV CARD, MITAC P/N 531707310004, DATE 0504. TUNER TSEJ1-203A ALPS JAPAN - B400L4I


I need the software driver for my NEC TV CARD, MITAC P/N 531707.... DATE 0506 - G1BDA B6

Mar 07, 2009 | PC Desktops

3 Answers

When installing a new hard drive the system bios recognize the drive. However, when I start to install Windows XP, the program does not see the drive as being present. How can I get the computer started...


What type of hard drive is it. Sound like you put in a SATA hard drive. You need to load the drivers for that hard drive. During the Windows XP setup it gives you an option to load 3rd party drivers that what is sounds like you need to to.

Mar 05, 2009 | Dell Dimension 8400 PC Desktop

1 Answer

Computer system problem


Your hard disk might be SATA interface, and XP don't have access to this type of hardisk. It requires RAD driver for that type of disk.

1). You can make your HDD accessable to XP by disabling the SATA mode in your system BIOS setup. Then XP will access your HDD and it will be installed.

2). You can also make your HDD accessable to XP by atchi driver. Go to your motherboard manufacturer site and download SATA driver according to model number. This may be compressed or auto extract exe. Extract all files and copy it into a floppy disk. Then start your XP and press F6 at first screen, then it will be prompted to insert RAD driver from setup, follow the instructions and XP will be installed on your system.

Thanks
Iqbal

Mar 18, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...