Question about HP Color LaserJet 2600n Printer

1 Answer

OHP sheet apparently jammed within the printer

I put in an OHP transparency, and got out half of the picture on (the next) plain page, but no sign of my transparency. Now the printer will no longer print, and I can't see where the transparency has gone - error shows in the top section, but how do I remove the top or get access to that area to find where it is jammed?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

There should be an access door on the back of the printer. Open it up and I think you will find your transparancy in there. If it is,, pull it out from the back door and not the front.

If you cann't see it, leave the door open, remove all paper from the tray, and then press the feed button.

Posted on Aug 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disactivate or bypass the OHP sensor on the phaser for semi opaque paper (calc paper)?


Hi Rich,
Thank you for your lengthy and informative question that does help.
My first thoughts:
Did you try and tell the driver what particular type of paper you wanted to print on such as none Xerox recommended.
A thought just occurred if you were wanting to print transparencies then the printer would have to print strong colours at 100% because once you place the image on a OHP the image would look really washed out.
All the Xerox printers I've ever worked on don't have sensors that look at the opaqueness of the media, they do however have transparency sensors because once the edge of the paper has been detected a jam could occur, so lever type sensors are used to actually feel the media.
Good luck.

May 26, 2015 | Xerox Phaser 7400DN Laser Printer

1 Answer

Can I print envelopes on my Bizhub 250


BYPASS TRAY is sed when printing onto paper with a size not loaded into a paper tray or onto thick paper, overhead projector transparencies, postcards, envelopes or label sheets Can be loaded with up to 150 sheets of plain paper, 50 overhead projector transparencies, postcards, label sheets or sheets of thick paper, or 10 envelopes referred to as the "bypass tray" throughout the manual. (See page 2-60....ATTACHED )
ftp://207.18.56.26/software/BPG/Userbizhub200250350CopyOperPh2_5.pdf

Feb 15, 2011 | Konica Minolta bizhub 250 All-In-One Laser...

1 Answer

When printing in color, the color runs


Specifications state the following:


Plain paper (16 lb to 24 lb),


thick paper 1 (24-1/4 lb to 40 lb),


thick paper 2 (40-1/4lb to 55-1/2 lb),


thick paper 3 (55-3/4 lb to 68 lb),


thick paper 4 (68-1/4 lb to 72 lb), OHP transparencies, postcards*, letterheads,


colored paper, envelopes, label sheets, banner paper (24-1/4 lb to 55-1/2 lb)*


Duplex: Plain paper (17 lb to 24 lb), thick paper1/2/3 (24 lb to 68 lb


*Can only be fed through the bypass tray.


These specs are directly from the user guide.


Is the paper running through the bypass tray

Jul 13, 2010 | Samsung CLX-2160N All-In-One Printer

1 Answer

HP laserjet 4L paper jam after printing one page.


You need the pick up rollers replaced. Call your service centre to replace pick rollers as these are feeding the pages crocked

Aug 31, 2009 | HP LaserJet 4L Printer

1 Answer

Paper settings


When you change the settings do you hot then 'OK' button to see that the astix is next to it ? When changing settings make sure that you see that astrix next to your changes if not you will return to it's original setting. I alreaded assumed you knew how to access the menu's Make sure you set these setting by"OK" some printers like "Xerox" will make you hit the "Select" key


Mar 04, 2009 | Lexmark C522n Laser Printer

2 Answers

Epson artisan 800 wont print to a transparency


OK so i tricked my 810 into printing on a transparency. NOT that I recommend doing this ... but .... I took four pieces of clear tape and taped the top (where it goes into the printer) and on each side about three inches from the top.

Then I put it in the tray with the transparency on the bottom of the paper -- since it brings it up thru the printer and flips it over, it prints right onto the transparency !!!

It didn't like it the first time, since I just folded over the tape on the end that gets sucked into the printer first. Hence the added stabilizers on each side.

Feb 15, 2009 | Printers & Copiers

1 Answer

Printer feeds 1 and a half pages and jams every time.


PUT 1 sheet in at a time nd it will be fine
just dont put loadz in at da same time

Oct 17, 2008 | HP Officejet 5610 All-In-One InkJet...

3 Answers

Printer Jam - when i put a sheet of Avery labels, printer jams


When you say TOP TRAY, do you mean a paper drawer, or the BYPASS TRAY? If the labels won't feed into the bypass but bond paper does, check to see if your labels are made for inkjet printers. Go to www.avery.com and contact Avery customer support to see what product they recommend for your MFC. Labels made for plain paper printers sometimes do not work for inkjets, and vice-a-versa.

Aug 29, 2008 | Brother MFC-5840CN All-In-One InkJet...

1 Answer

USING OHP TRANSPARENCIES


You can't use ordinary transparencies if you use ink... find a special transparency that is sold by Espon, but that's rare to find now... only Laser printers can print color or black on ordinary transparency

Oct 18, 2007 | Epson Stylus C64 InkJet Printer

Not finding what you are looking for?
HP Color LaserJet 2600n Printer Logo

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...