Question about Bernina Artista 180

1 Answer

I have a Bernina Aurora 430 (not on your list). For some reason, the feed dogs have dropped. The button that usually drops them isn't working.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

If you remove the metal plate on the bottom of your machine, you can see the workings of the feed dog raise and lower button. With some luck it just might be a screw that came out or it might be a broken spring inside the sewing arm.
Without a service manual or a view of what it should look like inside when it is functioning correctly, at best you would just be guessing. It should be a simple 5 min fix but it is best to take it to a Bernina dealer for proper repair. Good luck, bushvideo

Posted on Sep 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't drop the feed dogs on my Bernina 1260


Could it be that the feed dog mechanism has not been oiled for a long time? I have a 930 and perform frequent all-over oiling including the feed dog mechanism (all-over refers to a couple drops of good quality sewing machine oil every place where metal rubs on metal). To get them working faster, try directing hot air from hairdryer into the internal mechanics to loosen things.

How can get the reverse lever to work Sewing Machines

It was working now it seems to be frozen the needle part wont move

...

Feb 08, 2016 | Sewing Machines

2 Answers

My Bernina 930 does not feed the fabric through the feed dogs. Hoe do I fix this?


Did you unknowingly drop the feed dogs, as for darning? It is the lowest knob on the right, the silver dial in the center raises and lowers the feed dogs.

Feb 27, 2015 | Bernina Sewing Machines

1 Answer

Need to remove needle plate


Remove the presser foot and needle. Press the feed-dog drop button on the right-hand end of the machine, so that the feed-dogs drop below the needle plate. Press the back right-hand-side of the needle plate firmly and the front left side should pop up. You can then lift the plate out to clean underneath etc. When replacing, put the hole in the plate over the locating lug at the front-right corner and make sure the right-hand-side of the plate is down first, before pressing the left-hand side down into the grey surround. Be careful not to use excess force if it wont go, otherwise you could break the retaining spring. When done, dont forget to press the feed-dog drop button again and rotate the handwheel once, so that the feed-dogs come back up again.'

Hope that helps

Jan 27, 2012 | Bernina Artista 180

1 Answer

Location of control for feed dog Bernina Virtuosa 150


I assume you mean the feed dog drop button, which is a square button in the base of the machine at the right-hand (handwheel) end of the machine, about one-third of the way back. Press it once to drop the dogs, again, to allow them to come back up.

Aug 26, 2011 | Bernina Virtuosa 150

1 Answer

How do you oil a Bernina Activa 130? The manual doesn't say anything about it.


Remove needle, needleplate, presser foot and bobbin case. Now take a lint brush and clean under the feed dogs and hook area. take the bernina oiler(must be bernina oil only) now place a drop just below where the bobbin case clip on and one small drop under the feed dog area. replace items, sew out a test sample and away you go.

Apr 27, 2010 | Bernina Activa 130

1 Answer

How do you oil a Bernina 170?


Remove needle, needleplate, presser foot and bobbin case. Now take a lint brush and clean under the feed dogs and hook area. take the bernina oiler(must be bernina oil only) now place a drop just below where the bobbin case clip on and one small drop under the feed dog area. replace items, sew out a test sample and away you go

Apr 25, 2010 | Bernina Artista 170

2 Answers

Bernina 240, won't complete the buttonhole


Double check the instructions and if there is still an issue, call the Bernina dealer and tell them what is wrong.

Ask if someone will be available to look at the machine when you come in .... you need one-on-one assistance.

Mar 07, 2010 | Bernina Sewing Machines

1 Answer

Aurora 430 Bernina


Hi, possibly your feedogs are dropped and in the darning position and/or its thinking you want to embroider and there is NO hoop attached or entire embroidery unit plugged in. Check your feedog button below the handwheel on the bottom.
Rick

Jul 29, 2009 | Bernina Sewing Machines

Not finding what you are looking for?
Sewing Machines Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bernina Sewing Machines Experts

Derek Massey

Level 2 Expert

92 Answers

Page Gettman

Level 1 Expert

30 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Are you a Bernina Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...