I have a hot point stove with fuses.Ineed to know in what order and what size I need. I have no manual, so Ihope you can help me. Model no.KE638JW-1 Type 340. Serial no. LB136758. The fuses were removed and put in wrong.

Stove conversion natural gas to Lp - YouTube

? 6:08
https://www.youtube.com/watch?v=iXX2mS6FrxI
Sep 2, 2014 - Uploaded by Clay Rogers
If anyone can do it so can you. ... Stove conversion natural gas to Lp ... How to Convert Your Natrual Gas ...

If you have a pilotless model it is very likely that your oven igniter is bad. This is fairly easy to replace. A contunuity check will show if the igniter is bad.

kitchen.manualsonline.com does not show a manual for your model. Hotpoint's official site doesn't list your model number. Are you sure of the model #? How old is this stove and what country was it purchased? I have a search for information on your particular model going on, but nothing yet. At the above site there is a link in middle of the page to Hotpoint support and the right of that page is a phone# if you don't see your model#. I don't think its toll free. At this point I'm waiting some replies and have no further information. Hope that helps and I'll post anything new.

Pat, the model you have uses a 1 Lb tank, that can purchased at any hardware store or home center. It's the same size tank that Coleman stoves use. They run anywhere for $4,00 -$6.00.Unfortunately, you can't order full tanks, because of Hazmat issues in shipping to you.

Hope this helped you. Please let me know.

Here is the firing order for the 3.3 L6 and the 2.3 L4 Ford Fairmont

_

Hope helps.

FBT For D52W19byx2 #259296
Encompass Parts Distribution 1-800-638-3328 Go to this website and type in your Model Number they List Parts/Part# and Price of part.

UED is another company that has Parts for this set 1-800-648-6657

THERE ARE 2 FUSE BOXES, 1 UNDER THE HOOD & 1 INSIDE THE CAR. TURN ON IGNITION SWITCH TEST EACH FUSE WITH A GOOD FUSE TESTER. FUSES CAN BE TESTED WITHOUT REMOVING THE FUSE FROM THE FUSE BOX. THERE ARE TEST POINTS ON EACH FUSE FACING OUT. POWER ON ONE SIDE OF THE FUSE, FUSE IS BAD. POWER ON BOTH SIDES OF THE FUSE IT'S O.K.

If you are talking about the fuse on the circut board, it tells you the size on the black cover, covering the circut board. I think it's a 1 amp and 3 amp glass fuse.

Hello rcgrecco,
I will try to assist you but will be making some assumptions based on your problem description. First off, when you say it takes a few tries torest the fuses.. are you referring to circuit breakers? or changing out fuses a few time until it begins to work ok? In either case, the fact that it is drawing more current than the service ( fused or circuit breaker protected implies that you have one of two problems, 1. undersized service ( meaning the fuse of circuit breaker which protect the circuit is under-sized) or 2. a short internal to the stove or receptacle that supplies power to that stove.
I would approach a solution in this manner. Remove or disable power to the stove then open the wall receptacle and ( with power verified and off) tighten all wire junctions.. I have seen cases where a loose wire termination becomes resistive and then in order to meet power demand at the burner, more current is drawn which in turn causes the breaker or fuse to trip..) I would also check the terminations at the point of entry for the power cord at the stove. Make sure all the wire terminations are tight. Once you've done that, try turning on one burner at a time and see if the service remains on or trips the protector ( fuse/breaker) I wouldn't use the oven until I verified that each burner works OK.. then try the oven by itself.. and add a burner .. then two.. ( the point being is to try to determine if you have one of the heating elements shorting. 12:00 flashing is the default time setting after power is lost and restarted. I am almost 'questioning your electricians findings" since circuits do not trip unless there is a fault ( too much current being drawn or the service is under-sized for that oven) or... the circuit protection in and of itself is failing due to marginal components. The fact that it is getting worse suggests that whatever was shorting is shorting more frequently.. perhaps a heating element is shorting after it gets hot.. they are typically resistive elements and it is possible for a short to develop between the core material and the protective jacket.. I hope that helps you... or at least provides a few ideas on where to look...
Regards,
Rick

Ineed amanual for my hotpoint oven so i can clen it