Question about Jacuzzi Garden

Open Question

Jacuzzi pump s/n 91110890 model #1e112-8 date 24b95 looking for parts availability & or parts list having problem getting up to pressure it's a jet pump thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jgwhomeequip
  • 1902 Answers

SOURCE: Jacuzzi jets not pumping out water

Check the jet pump, also where the filter is there are two 90s plastic. make sure that they are both in the water, if all those check out then check the switch for the jets. It sounds like the pump is bad and is not pumping the water. Even if the motor works and the internal parts of the motor seal gets wet then it all needs to be replaced and rebuilt. Very easy to do yourself. Like always be careful and unplug the unit.

Posted on Feb 11, 2009

Ad
  • 3 Answers

SOURCE: karcher k2400hh pressure washer, water pressure cuts out.

Hello cikanek:

Try this:

From your posting, I assume you have removed the splash cap and the nylon bypass valve cover. Connect the water supply to the pump and connect the high pressure hose and wand to the pump outlet. Wad up a small towel and place it over the bypass valve opening to catch the valve insert when it pops out. With the engine throttle closed, pull the starter cord several times to see it the valve insert will pop out. If it doesn't come out after two or three pulls, set the throttle to low and start the engine. I have performed this procedure a number of times and the valve insert always pops out. There is no real danger of the valve parts getting seriously airborn since the actual pump output volume is very low (2.5 Gal/min).

Good luck,
Ed

Posted on May 23, 2009

SOURCE: 5 year old Laars 25,000 LX won't ignite.

The low pressure indicator is for the gas pressure not the water pressure. The heater won't ignite because it's not getting gas to the igniter. Check gas supply, if okay, check gas connections, valves, etc.

The 1 HP motor should be fine on the jacuzzi.

Posted on May 26, 2009

boysor2933
  • 293 Answers

SOURCE: I have a Jacuzzi Jet Pump Model 7C-S/B. Not Working

Check the breaker that supplies power to the unit. If it is in tripped position, check if the motor is grounded ( continuity between terminals and motor body), check for shorted windings (infinity resistance value between the winding phases), and finally check if the pump is stuck up due to debris or defective motor or pump bearings.

Posted on Jun 11, 2009

  • 31 Answers

SOURCE: My American Standard whirlpool pump will only hum.

The bearings (or bushings) of the pump or pump motor have siezed, these can be replaced on some models but for the most part you will need to replace the pump and/or pump motor. and as where to get parts, i would suggest the outlet from wich you purchased the unit or another appliance outlet. Or if you feel up to the challenge, im sure you could find replacement parts on the internet: google, ebay, etc.

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the on/off switch on my jacuzzi pool pump


you might not be able to replace the switch parts might not be available jacuzzi is out of business you might be able to replace the motor if not get a new pump they can cross reference for you

Jul 28, 2014 | Jacuzzi Pool & Spa

1 Answer

Jacuzzi hot tub replacement jets


your local jacuzzi dealer should be able to source you some parts , but i can tell you if it's only a o-ring failure these are avail from your local hardware store , as most jets are rebuildable , some are not look at back for screws to see if they are or not

May 20, 2014 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

I have a jacuzzi amiga N890 that when you turn the unit on it just hmmms. It is getting power but does nothing else accept hmmm.


If you turn the Jacuzzi pump on and it just hums and no water flows through the jets then you have a bad pump.
You will need to get the brand name of the pump and the model number before you can begin your search to find the proper replacement.
Bath Pumps each have their own size. You will want to find the exact brand so you do not have to change any of the plumbing.

US Parts Center

Aug 20, 2013 | Jacuzzi Amiga Whirlpool JAC-N890...

1 Answer

I'm trying to find a seal kit for a Emerson spa pump Model #T55MWCCE-1208


The seals are specific to the Jacuzzi pump housing not to the Emerson motor. Most Jacuzzi pumps use the PS-200 or PS-201 seal (some have it listed as AS-20X) here is a Pump Seal Cross Reference.

Jul 25, 2012 | Emerson Pool & Spa

1 Answer

I need a motor end cover, where can I get one? Thank you!


Jacuzzi (Carvin) Magnum, Force & Plus pump parts are hard to find.
Here is a link to our site which has a parts explosion/diagram for those pumps.
Jacuzzi Magnum, Magnum Plus, and Magnum Force Pumps

Jun 08, 2011 | Jacuzzi MAGNUM FORCE POOL PUMP 2 HP...

1 Answer

How to separate the two impeller flanges of a jacuzzi pump to access the impeller in order to remove the wet end from the motor OR is there some way to remove the wet end of a white JWB 60C Ser no. 06785...


That is an old sealed Jacuzzi pump that can not be repaired. It is one of many reasons why Jacuzzi never did well in the pump business and has gone from owner to owner over the years. Unfortunately your pump is not repairable without destroying it in the process.

Wet ends may still be available. The part numbers I have are:
850100 .5/.75 HP
9011000 1 HP
850200 1.5 HP
856600 2 HP

0199000 Gasket (2 req’d)
4516000 Flange, 2”

Good luck,
John

Aug 22, 2010 | Jacuzzi Impeller, L - 3/4 H.P

2 Answers

Need to order a replacement toilet seat for Model Jacuzzi Era toilet. We have looked at Lowe's and other home improvement stores and all the available elongated replacement toilet seats do not seem to be...


Try checking plumbing supply houses instead of home improvement stores. Im not sure where you are located. Here in MO. I use Harry Cooper Supply or Riback Supply or Southern Materials. A good supply house should be able to help you find what you are looking for. Hope this helps.

May 04, 2010 | Jacuzzi BK37959 White Era?? Two-Piece...

1 Answer

Jacuzzi pump not pumping


I would probably say that the pump is clogged up or frozen. The motor humms until the heat sensor clicks it off. Try taking apart the front of pump and see if it turns and you should see the problem. Parts are available at most pool stores. Pumps are usually cheaper online.

Jun 25, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

Jacuzzi Magnum Force Pump not working


The number one problem is air leaks.......check all connections to see that they are tight, and rubber seals. The intake side would give you trouble with air leaks. If you dont find any leaks then I would pull the pump cover and check the impellor. Pool stores have parts and lots of knowledge.

Jun 09, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

Not finding what you are looking for?
Garden Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Garden Experts

john h

Level 3 Expert

12173 Answers

Jay Finke
Jay Finke

Level 3 Expert

1340 Answers

Ian Kime
Ian Kime

Level 2 Expert

77 Answers

Are you a Jacuzzi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...