Question about Navigon GPS

1 Answer

I really need a manual to set up the unit - Navigon GPS

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 17,970 Answers

Could send us the model?

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All the unit's digital controls seem to be in


Joe, There are 5 basic, but solvable reason for what you described. Please pay particular attention to numbers 1 & 2.

1. The humidity extraction level is set to HIGH. Lower it to 32-35%. If you have a manually
controlled unit.set the knob on maximum.

2. Air intake filter is dirty or clogged. Turn unit OFF, & Unplug the
Unit, before removing to inspect & clean it, if necessary. If washed,
allow filter to completely dry before reinstalling. DO NOT operate
the unit without the filter.

3. Obstructed air flow. Maintain a minimum of 12 to 18" of clear air
space around the entire unit.

4. Cooling coils are dirty and need to be cleaned. Use warm water & dish washing liquid to
clean the coils. Rinse and wipe dry. Apply a light coating of WD40 to the coils.

5. Ambient air temperature at floor level is between 40 - 60 degrees.
dehumidifiers do not work well between those temperatures
(Unless, you have a Low Temp Unit). This applies mainly to
where the air temperature at floor level is colder than at shoulder
level
in basement applications. Raising the unit up off the floor,
onto a sturdy table, counter top, etc, that can handle the weight
of the unit, plus a full tank of water, will usually resolve this
problem.

If none of the above solves the problem, it may be a case of the compressor needs to be recharged with refrigerant gas or that the humidity condenser sensor has failed. These things usually occur in units that are 5 years old or older. It's rare in a unit younger than that. But, it can happen.

I really hope this helped you to troubleshoot and solve the problem.
Please let me know.

Jul 20, 2011 | DeLonghi Dehumidifiers

1 Answer

Incoming volume contol


you really need to advise what type of unit system you have ,majority have a dial underneath the unit that increases the tone ,it might also need a digital prompt that is by pressing a few digits this may enhance or decrease the incoming tone please refer to your manual .
each unit has different settings.
Best regards
John

Mar 14, 2011 | Lands Phones

2 Answers

I was given a Linksys WRT5462 without any manual setup CD. Can you pls advise me how to go about doing that?


Linsys Tech support for the USA is 1-800-326-7114. Would start there. Good luck,Liberty.

Jan 20, 2011 | Linksys Wireless-G Broadband Router

1 Answer

Acu-Rite 00754 Wireless Weather Station manual


The main thing with this unit is to put the batteries in the transmitter first, then in the base receiving unit. Then you can't really make any setting changes until the unit figures out the correct time through the radio signals it receives from Colorado, or wherever they come from.

Aug 27, 2010 | Office Equipment & Supplies

1 Answer

Says to clean the air filter


The air filter on this set is on the bottom of the light engine which means you have to remove the light engine form the set to access the filter, i have the guide right from panasonic service manual, no picture as the manual does not have one but here is the info:
######################################################
THE FILTER ON THE PROJECTION UNIT
CAUTION:
Operating with torn or damaged Air Filter may cause damage
to the Projection unit.
Remove the Projection Unit from rear.
The filters are located on the bottom and in new engine
designed the front of the engine.
clean the filters onthe Projection Unit. Gently remove any
accumulated dust from
filter with a vacuum cleaner; use extreme care so as not to
damage or tear the filters.
############################################################

The engine is a little tricky to get out you really need to be sure each connector removed is inserted and no cable has stress on it when it is being removed, there are no photos of the process just a tech jargon from the service manual.

Hope this helps,


Apr 01, 2010 | Panasonic PT-52LCX66 Projection Television

1 Answer

UNIT NOT BLOWING WARM AIR-OR REACHING DESIRED TEMP


I assume this is a heat pump. The outside unit may be icing up. It should have a defrost cycle with electronic control that sometimes fails or sensor associated with the electronic determination of when to defrost may have failed or may not be sensing because its out of position. You can check for a defrost problem. If frost is blocking the outside unit air will not pass through it after the frost builds up and you may be able to see the white frost as well. If all this is true you need to get a service manual and use its procedures to find out why the unit is not defrosting.

Jan 12, 2009 | Weather King 12AJA4801AH Air Conditioner

1 Answer

Second hand set doesn't work


The second hand set problem was resolved by placing it face down on the base unit. Apparently it needed to be reset for some quirky reason.

I found the solution in the manual, and although it didn't really address the problem, I thought it was worth a try. It worked.

Feb 17, 2008 | Uniden TRU 448-2 Cordless Phone

1 Answer

Bulb Reset issue


I had the same problem and called Sony, they just said to keep trying what the manual says to do, but make sure the unit is in standby mode. I tried in powered mode and in standby mode many times and it did not work. Then I tried again the next day when the unit had been in standby mode for an extended time period. I hit the four buttons like the manual said, all four in quick succession. I also tried the four buttons in many different sequences from what the manual said. When I powered back up the lamp timer was set to zero, finally! I think having the unit in standby for an extended time was the key. The Sony rep really emphasized the need for the unit to be in standby.

Oct 01, 2007 | Sony VPL PX40 Multimedia Projector

Not finding what you are looking for?
GPS Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Navigon GPS Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

perdue40

Level 3 Expert

587 Answers

Are you a Navigon GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...