Question about Blade Oster Cryogen X Agion A5 Clipper Size 10

1 Answer

Blades wont cut. they are new, clean and appear to be in right.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 193 Answers

If your blade is connected fully and the clipper is driving them then it sounds as though it may be a clipper fault without seeing them its hard to say what but the most likely is the Lever which wears in width.

Posted on Aug 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Cricut Explore Air wont cut


If your Cricut machine is not cutting all the way through your material, or is only scoring the material, choose a machine below for specific troubleshooting tips. Fortunately this issue can usually be resolved with basic troubleshooting.

correct cut settings.
  • Remove the blade housing, then remove the blade and ensure that there are not any bits of paper stuck to the blade or lodged inside the blade housing. Ensure that you replace the blade housing correctly into the machine. Once clean, test your cuts again. If the blade and housing are already free from debris, or cleaning it did not help, proceed to 3.
  • Try an arm buoyancy test: gently press down on the black arms that surround the blade housing and then release them. Do they bounce right back up, or do they stick or rub in any way? If they stick or rub, please contact Customer Care through one of the options below for further assistance. If they bounce right back up when released, proceed to 4.
  • Increase the machine pressure settings and try your cuts again. If this does not change the cut result, proceed to 5.
  • Increase blade depth by turning the dial at the top of the blade housing. If this does not change the cut result, proceed to 6.
  • Perform a Hard Reset on the machine. If this does not help, proceed to 7.
  • Check your machine's firmware version. If the firmware is not up to date, perform a Firmware Update using Cricut Craft Room, a Gypsy device, or Cricut Design Studio.
  • Retry your cuts with a new blade housing.
  • If the machine is still not cutting through materials, or is only scoring the paper, please contact Customer Care through one of the options below for further assistance.
  • Forced Firmware Update on the machine through Cricut Sync.
  • Retry your cuts with a new blade housing. If the issue persists, proceed to 8.
  • Attempt a Format and Restore on the machine through Cricut Sync. Please note that this step should only be taken if all other steps have failed to resolve the issue.
  • If this does not resolve the issue, please contact Customer Care through one of the options below for assistance.
  • new blade. If this does not help, proceed to 5.
  • Adjust/increase the Multi-Cut setting in the Cricut Craft Room cut preview screen and retry your cuts. If this does not change the cut result, proceed to 6.
  • Retry a cut using a new blade housing.
  • If the machine is still only scoring or not cutting through the material, please contact Customer Care through one of the options below for assistance.
  • Jan 16, 2017 | Crafts & Hobbies

    1 Answer

    Clippers have suddenly stopped cutting and seem to pull at the hair


    Generally removing the two screws.. on the blade foot (don't do this over the sink unless the drain is closed!).. and taking the blade apart.. cleaning the trimmers with a small brush.. apply grease in the blade groove.. reassemble

    Usually it's best to put those two screws back just get them in lose.. not quite snug..set the blade upside down on a flat surface..so it pushes the blade back away from the cutting end..level..then tighten those screws while you are pushing or holding down on the clippers cutting edge against the flat surface/table. ... oil the blade with the proper oil or a light mineral oil.

    This usually will get them back to cutting properly..the blade should be oiled prior to each use...about two to three drops right along the visible part..or a light spray also hair should be clean.. dirty hair does not cut well at all..and the clippers will tug and pull rather than cut cleanly.

    Lastly..if they see a lot of use. might be blade replacement time..

    Best of luck!

    Apr 13, 2011 | Oster 76076-010 Hair Trimmer

    1 Answer

    42 inch jd la115, hit stump in yard, changed blade cause I thought I bent the baldes still cuts uneven. Could the shaft be bent or broken? It appears to be cutting properly on the right side but the left...


    try pushing the blade up into the deck,,,if there is any lift in it there is the fault,,the top nut has come off the blabe drive pully and let the drive shaft drop a little this will lower the cutting blade,,,fix it before the blade falls right out

    Aug 15, 2010 | John Deere Garden

    1 Answer

    A5 Golden Oster trimmer


    alignment is of and blade needs cleaning and oiling

    Dec 19, 2009 | Health & Beauty

    1 Answer

    Have to overlap about half my cutting deck to get clean cut.


    A: Is the blade on right?

    B: Is the belt on the pulley?

    C: Is the blade tight on the spindle?

    D: Does the spindle turn freely with the belt off?

    I can't think of any other possibilities

    Jul 03, 2009 | Craftsman 21 Hp 42" Deck, Ys 4500 Lawn...

    2 Answers

    Misses hair when cutting


    You probably need a new blade drive, which is easily replaced yourself, if you are so inclined.

    Apr 20, 2009 | Andis 01690 Hair Trimmer

    Not finding what you are looking for?
    Blade Oster Cryogen X Agion A5 Clipper Size 10 Logo

    Related Topics:

    210 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Blade Health & Beauty Experts

    Anglia Clipper...

    Level 2 Expert

    193 Answers

    Joseph Hoffmann

    Level 3 Expert

    1702 Answers

    Bill Boyd

    Level 3 Expert

    44293 Answers

    Are you a Blade Health and Beauty Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...