Question about Dryers

Open Question

I have a Simpson Eziset 550. I need to replace the spigot that holds the lint filter in. How do I get to the back?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: washing machine lid switch

used my noggin and saved $20-00

Posted on Dec 29, 2008

Ad
  • 142 Answers

SOURCE: clothes dryer stops

sounds like the drive belt has stretched, or the auto tension is low.
disconnect power and remove back cover, clean inside around motor resitor block wires, and inspect/ replace faulty components. good luck!

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: Bad smell in Simpson Eziset 550

pour a few litres of vinegar in the machine on low level of water and do a wash with no clothes in it. should clean tub and drain hose

Posted on Sep 12, 2009

hattonhall
  • 349 Answers

SOURCE: simpson eziset 800 clothes tangle when washing

If you can use a lollipop stick to operate the lid switch while you leave the lid open, you will be able to observe if the agitator is going smoothly back and forth EVENLY or not. If it is tending to turn just one way....this will tangle the clothing like mad!
If this is the problem it could be the switching module or capacitor that needs replacing.

Posted on Oct 25, 2009

Testimonial: "i will try it thanks "

  • 3 Answers

SOURCE: My simpson eziset 550 washing machine just stopped

Replace the fuse inside the control panel make sure you turn if off.
depending on where you are the fuse is more than likly a "4amp slow blow" fuse
hope this helps

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Simpson Eziset 550 and I press the power button and get nothing


Either power on/off switch is faulty or main control board has a fault and may have to be replaced. You need a test meter and fault finding knowledge to trace the fault. Probably best you call out a service person.

Feb 17, 2018 | Simpson Washing Machines

1 Answer

Where is the lint filter on a Simpson Eziset 950 top loader washer?


lint filters for simpons top loader is at the bottom of the center lift out piece in the agitator
just pull the lot up and the lint filter is a small pocket at the end of it

Dec 10, 2015 | Simpson Washing Machines

1 Answer

My Eziset Simpson 550 won't spin


either the motor brushes are badly worn
or the pump cant clear out the water

i would say check the brushes they should be quite long if they are shorter than 3/4 inch then replace them

Mar 09, 2015 | Simpson Washing Machines

1 Answer

Eziset 550 Drains as it fills


Replace the fuse inside the control panel make sure you turn if off.
depending on where you are the fuse is more than likly a "4amp slow blow" fuse
hope this helps

Dec 02, 2012 | Washing Machines

2 Answers

Simpson eziset 550 stops at rinse cycle, light flashing


I had the same problem before, but removing the kink in drain hose does the trick. Maybe yours is more complicated but try it.

Aug 28, 2012 | Washing Machines

2 Answers

Bad smell in Simpson Eziset 550


pour a few litres of vinegar in the machine on low level of water and do a wash with no clothes in it. should clean tub and drain hose

Sep 06, 2009 | Washing Machines

7 Answers

Hi, my simpson eziset 550 washing machine wont start, I press power on then the start button and beeping alarm starts with the three water temp lights flashng, this has happened intermitantly in the past...


5 beeps with the 3 temp lights flashing means lids not closed. or lid switch not working

i just fixed this problem. the magnet in the lid had come loose. I undid the two screws on the side of the lid put the magnet back where it should sit then i poured candle wax over it to hold it in place and working fine now.

Nov 30, 2008 | Washing Machines

Not finding what you are looking for?
Dryers Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

16981 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...