Question about Sunbeam 722 Auto Shut-Off Heating Pad Heater

1 Answer

I just got my new heating pad. All it does is flash F2. Last night was the first time to use. Why is it doing this? I do not have a manual for the pad "misplaced". Tried to download and it will not. Please help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,323 Answers

Hi

As its new I would recommend you to get use warranty and get it repaired/replaced. However, if you still want to do this yourself then pull out the main wire box located inside the pad and then take it apart and use hair dryer to dry the electronic control board, this should work, however remember that opening it will void the warranty. Hope this helps...please post back for further assistance.

Daniel

Posted on May 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Get F2 error code on sunbeam heating pad model cat93, contrller sw404


Crimped the ends of the heating pad cord where it attaches to the pad a little then did the plug and unplug three times while holding down the on-off button and that did the trick

Jul 03, 2011 | Sunbeam 805810 HeatSense Heating Pad...

1 Answer

I bought a Sunbeam Heating Pad (Ultraheat) last year which I just took it out of the box last night. It is brand new, not used until last night and it smell like it was burning. I instantly unplugged it....


Sorry to read about your problem, I hope this helps you out.

i think from sitting in the box for a year, the material can smell, form its first time usage.
I suggest you put the pad on or in a baking dish on the stove..plug in and see if the smell burns off. I think it will.

if not return to Sunbeam (800) 435-1250


I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful



Dec 31, 2010 | Sunbeam 722 Heater

1 Answer

Dream Maker Hot tub - Display is blank - no #'s - flashes 4 times


Hard to say without being there. Two things to check though. First be sure the new board is the correct one. Many times parts will change and replacements will have special instructions for retrofitting.
The other thing to check is be very sure the plug on the new board lines up with the receptor. On a multi pin plug if the pins don't line up you can get just the problem you describe. I hope this helps, sorry it can't be more.

Feb 28, 2010 | Dream Maker Spas Dream Maker Ez Spa Hot...

1 Answer

I HAVE A MAYTAG BUILT IN OVEN THAT WAS WORKING FINE LAST NIGHT AND GET UP THIS MORNING TO BAKE AND I AM GETTING, ITS FLASHING A F2 AND F7 ERROR CODE AND THE ALARM OR BEEPING IS GOING OFF


Hi You have a bad touch pad , there maybe a be a button stuck in , try running your fingers over all the touch buttons but i think the touch pad will need to be replaced as always remove the power before taking it a part

Dec 21, 2009 | Maytag CWE4800A Electric Single Oven

2 Answers

F2 and F3 Errors just started on my GE Electric Range


I had to clean the contacts in the control panel to fix my same problem.

Nov 10, 2009 | GE Kitchen Ranges

10 Answers

F2 Fault Code On Heating Pad


I am trying something now as I was told F2 requires you to check the blanket for wear and tear and plug it back in. 3 times doing this should be sufficient. If it still reads F2 it's "gone" Ours is new so it shouldn't be "gone" but here's what I found...Where the plug goes into the blanket there are 4 holes for 4 silver pins. I noticed the 3rd pin was a bit lower than the other 3. It will not move up with pliers so don't force it just return it. check there

Jan 10, 2009 | Sunbeam 722 Auto Shut-Off Heating Pad...

4 Answers

Malfunction heating pad


Same F2, quick off problem here. Then I noticed that the gray plug on the power cord was not completely flush with the connector on the pad. I shoved them together until there is no gap. The unit's worked perfectly since then.

Mar 24, 2008 | Sunbeam 805810 HeatSense Heating Pad...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sunbeam Heating & Cooling Experts

paulcarew

Level 3 Expert

2518 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Jay Finke
Jay Finke

Level 3 Expert

1340 Answers

Are you a Sunbeam Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...