Question about Kirby G4 Bagged Upright Vacuum

Open Question

Whys my kirby g4 not working - Kirby G4 Bagged Upright Vacuum

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
b0sslady2001
  • 357 Answers

SOURCE: Manual and tools kirby g4

The first link is instructions for changing a belt. The second is for the shampooer instructions. If you click on the links below, it will take you to my online guides and if you look there, your other question will be answered. Thanks!!
Marci

http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039

http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992

Posted on Nov 09, 2007

Ad
b0sslady2001
  • 357 Answers

SOURCE: Kirby G4 plugged????

Check out my troubleshooting guide...just click on this link...
http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
Hope it helps...
Marci

Posted on Jan 05, 2008

Yozzer6821
  • 116 Answers

SOURCE: kirby g4 vaccum

please clarify what you mean?
Do you mean motor bearings or brush roll bearings?
brush roll bearings can be adjusted to lower the brush closer to the carpet when worn.
to do this remove the front brush assembly, there is usually a sticker below the belt hole showing RED = POSITION 1 HIGHEST (ie a new brush roll)
GREEN = POSITION 2 MIDDLE (brush part worn)
BLACK = POSITION 3 LOWEST (brush fully worn)
At each side of this there are 2 clips unlock these and remove the bottom cover.
Release the belt tension by rotating the belt release at the front.
Before removing the brush roll, at each end of the brush roll there is a grey plastic bearing carrier (Square at the ends) MARK this with a pen or marker just so you know the original position, also look closely for the coloured markings as indicated above or numbering 1,2 or 3.
If RED or "1" is showing you need to remove the brush roll by pulling it out and rotate the endcaps to Green or "2" and re-insert the brush roll, If Green or "2" is showing then rotate the endcaps to Black or "3" and re-insert.
If Black or "3" is showing then the brush roll is worn and cannot be adjusted any more, fit a new brush roll and insert with RED or "1" showing.
To re-attach the belt, move the belt to the middle of the roll and rotate the belt knob at the front ensuring the belt engages with the hook on the inside.

Posted on Jun 29, 2009

  • 7 Answers

SOURCE: Kirby G4 Vacuum/Shampooer

i find the kirby carpet washer is rubbish coz it leaves all the dirty water in your carpet and it goes smelly!

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kirby g4 stoped working


cable has shorted out internally, will need new cable

Nov 18, 2012 | Kirby G4 Bagged Upright Vacuum

1 Answer

Looking for a Kirby G4 impeller?


Hi There. Here's the Impeller Blad, or Fan assembly for your Kirby G4. Hope this helped you.

Please leave feedback or rate the repair helpful if this answered your question, thanks!

Kirby Impeller Blad Assembly

Thanks so much,

Chris Jones
GoVacuum.com

Dec 29, 2010 | Kirby G4 Bagged Upright Vacuum

1 Answer

Kirby G4 causes black streaking when shampooing carpet


Replace the belt it is probably worn. You can get a replacement here:

Kirby G4 Belt

Dec 06, 2009 | Kirby G4 Bagged Upright Vacuum

1 Answer

Kirby G4 Vacuum/Shampooer


i find the kirby carpet washer is rubbish coz it leaves all the dirty water in your carpet and it goes smelly!

Jul 06, 2009 | Kirby G4 Bagged Upright Vacuum

2 Answers

Kirby g4 brush wont turn belt ok


your belt has probably been stretched to the point where it will not work so good.

Jul 02, 2009 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

Putting on the attachments for the kirby g4


Well... some attachments you may end up not using at all... some of them are very handy...
I have online manual for attachments HERE

Good Luck

Mar 02, 2009 | Kirby G4 Bagged Upright Vacuum

2 Answers

Kirby G4 plugged????


Take the bag off of the vacuum, remove the paper bag, clean out the bag tube then put back on. Make sure that the tube is broken, it is, replave it.

Dec 29, 2007 | Kirby G4 Bagged Upright Vacuum

1 Answer

Manual and tools kirby g4


The first link is instructions for changing a belt. The second is for the shampooer instructions. If you click on the links below, it will take you to my online guides and if you look there, your other question will be answered. Thanks!!
Marci

http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039

http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992

Oct 29, 2007 | Kirby G4 Bagged Upright Vacuum

Not finding what you are looking for?
Kirby G4 Bagged Upright Vacuum Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

JoeVacs

Level 2 Expert

357 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...