Question about Linksys Wireless-G WAP54G 802.11g/b Wireless Access Point

1 Answer

Hi it seems that i cannot reset my settings on my access point, i press the access point but cant connect to it i cant obtain an ip address from the access point even that my settings is set to obtain ip address automatically

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

Try to reset your AP please.

Posted on May 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When my wireless access point is turned on, my computer is unable to renew the ip address. I show excellend signal strength, but "little or no connectivity"


Hi, Your computer is most like have IP address permanently asign. To change the setting for windows 7, click start, click control panel, click network & internet, click network sharing, click connection, click lower left hand property, click Internet protocol version 4 (TCP?IPv4), click property and click obtain and IP address automatically. Your Router will asign IP address. Windows XP, Click start, click connect to, click to show all connection, right click to the wireless connection adapter, click the property and click the down arrow click to TCP/IP, click the property and change it to obtain IP address automatically. That should work for you. Get back to us if this information help you solve you solve the problem. Good day now.

Jul 13, 2011 | NetGear WG602 802.11g/b Wireless Access...

2 Answers

Pleas help me , i can't connect to router becuose cant have ip gatewy i connect by ethernet to router bout cant access to it.


Router's default IP is usually written on its case, check user manual as well.

If you did not change anything in your network settings in your pc/laptop you should have dhcp turn on so press CTRL+SHIFT+ESC and task manager window should appear. Then File->Run.. and type 'cmd' and press ENTER. Black "dos" window should appear. Then type 'ipconfig /all' and press ENTER again and among lots of data you see you should find IP of your gateway.

May 08, 2011 | Cnet CWA-854 (CWA854) 802.11b/g Wireless...

1 Answer

I have a dwl-2100ap that was already configured in a network..so i wanted to use in other network..what i did is i reset it by pressing the reset button for more than 15 seconds.and i configured the...


Hi

Do not type the IP address and subnet mask, just click on obtaib the IP address automatically and obtain the DNS automatically. Because if you encode the IP and subnet mask, there would be conflict and let the internet explorer configure it automatically.

Please let me know if you need more help and please rate it if you believe that it might help you and others. Regards

Feb 27, 2011 | D-Link AirPlus Xtreme G DWL-2000AP...

2 Answers

HI SENAO 2611CB3 DELUXE REPAIR IP DONT HOW TO RECOVERY IP IP 192.1681.1. DEFAULT NO ANSWER NO CONNECTION THANKS LOST DEFAULT IP SAMMY


192.168.1.1
if you cant open it then reset router by pressing with toothpick the tiny button for 5 seconds while its on power.
if i was helpful please vote ..

Nov 01, 2010 | D-Link Computers & Internet

1 Answer

Can't connect to configure password through web address 192.168.0.50


When you reset the AP, how long did you press the reset button? To reset the AP to factory defaults, the reset button should be pressed and held for at least 15 seconds. Also, once reset, the AP should have the following settings:

IP address: 192.168.0.50
Subnet Mask: 255.255.255.0
Default admin username: admin
Default admin password: <blank>

When connecting your PC, either set an IP address within the same subnet (192.168.0.51 255.255.255.0) or choose "Obtain address automatically".

I hope this helps.

Dave Grannas

Jan 25, 2009 | D-Link AirPremier DWL-8200AP 802.11a,...

1 Answer

I cant reset my senao eoc3610


1 ) Check if IP address is the correct address of your Gateway.
Check if you can ping.
Be sure you have your Java enabled
Some router requires a specific Browser (IE6 or IE7) and cannot respond to different browser.
Be sure to remove any Java protection from your Browser.
Check with user manual if IP address requires also a specific port number ( 8080 or other).
Be sure to Connect Router using Lan cable
2) Change your PC IP setting to same subnet as your router
Control Panel / Network settings / properties of TCP/IP define an IP address and a subnet mask compatible with Router as gateway.
3) If you are not sure of Router IP address use reset button on router back to factory default; use this to configure router.

Dec 27, 2008 | EnGenius EOC-3220 (EOC3220)

1 Answer

Cannot log on to dwl2000ap


If the SSID changed to the default then you know that the router reset to the default settings and you should set your computer to automatically get its IP address via DHCP. I always set up my routers through a Wired connection first, just to setup the router and then go with the wireless. The default for the router should be 192.168.0.1 and subnet 255.255.255.0 . If the computer is set with a static IP address, change it to obtain an IP address automatically or the network card will not bother even looking for an address.

Aug 17, 2008 | D-Link AirPlus Xtreme G DWL-2000AP...

2 Answers

Senao 8610 not working


Are you saving your settings when you exit the setup screen?

Johnlgrn

Dec 29, 2007 | EnGenius / ECB-8610 / 54Mbps / 802.11a/b/g...

1 Answer

Unable to get connected to Belkin f5d6130 AP


Hi,

You need to be connected using  wired Ethernet (PC's LAN card to Router's Ethernet Port (at the back)).  This is the preferable INITIAL way to configure the router before going wireless. Also it would be to your advantage to initially set your PC (that will be used for configuring the router)  to "Specify an IP address" (static settings) and not "Obtain an IP address automatically."

For a PC connected via UTP networking cable attached to a Belkin F5D6130 AP, the networking settings could be:
IP Address 192.168.2.2
Subnet Mask 255.255.255.0
Default Gateway 19*2.168.2.1
DNS Server 192.168.2.1
Reboot

Post back results. Good luck and kind regards.

Oct 12, 2007 | Belkin (F5D6130) 802.11b Wireless Access...

Not finding what you are looking for?
Linksys Wireless-G WAP54G 802.11g/b Wireless Access Point Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...