We unpacked the Epson NX110 printer and did everything as we were supposed to. The printer compartment won't move out of the area under the right side of the printer. I nudged it out and put the cartridges in, but it still shows that there is no paper and no ink, even after we put the NEW epson cartridges that came with it in. Any suggestions?? This is very frustrating.

Find something electrical and plug it in to the wall socket to prove you have power there.

Make sure the wire is plugged into the back of the printer it is has a removable lead. Check if there is an off switch in that area.

Still nothing? It needs to go back.

All the details on your printer including troubleshooting tips are here. I recommend Canon or HP.

Epson Stylus NX110

Printer heads clogged or cartridges are empty or defective.

Sound like the scanner is the issue, is it under warranty? OR the Scanner may be locked, check for the scanner release device unlock it,.

You can download the Epson printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :-http://www.epson.com/cgi-bin/Store/jsp/index.do?BV_UseBVCookie=yes

For Epson Stylus Photo R280 general error You may contact Epson Customer Service for any kind of help you require. You can also call on Epson printer support phone number at +1-800-204-4427 and for UK customers the Toll free Number +44-800-046-5291 we are also provide technical support in AUS Toll free number is +61-1800-954-262.

Follow the link below:
http://files.support.epson.com/htmldocs/nx110_/nx110_ug/wwhelp/wwhimpl/js/html/wwhelp.htm

Click "replace ink cartriges" on the left of the page
and then select "Remove and install Cartriges"

Hello,

The Epson NX110 is in fact an ink jet printer.

http://files.support.epson.com/pdf/nx110_/nx110_sl.pdf

Thanks,

Pat

Find the NX110 in the printers section of the control panel. Then right click your printer and choose "Printing Preferences" then the "Maintenance" tab. In there you will see a button for 'Replace ink cartrige'. Select that and it will take you through it step by step and even move the print heads to the correct position so you can change the ink.

Press the Stop button. The print head moves to the position to indicate which cartridge is low or expended.

If you need more step by step instructions, follow this link...
http://files.support.epson.com/htmldocs/nx110_/nx110_ug/wwhelp/wwhimpl/js/html/wwhelp.htm

*** I'll be more than happy to help you on that.
there is a great possibility that the nozzles of your printer are clogged by dried inks.maybe cause by the previous inks that you just replaced. we can check that by printing a nozzle check pattern.

1. Load a few sheets of plain paper in the sheet feeder. 2. Turn off the Epson Stylus NX110 Series. 3. Hold down the Stop button as you press the On button to turn the Epson Stylus NX110 Series back on. When the On light begins to flash, release the Stop button. 4. Check the nozzle check pattern that prints to see if there are gaps in the lines. 5. If there are no gaps, the print head is clean and you can continue printing. If there are gaps or the pattern is faint, clean the print head. Using the Control Panel 1. Load a few sheets of plain paper in the sheet feeder. 2. Make sure the Epson Stylus NX110 Series is on and the ink light is off. 3. Hold down the Stop button for three seconds to start the cleaning cycle, which lasts around one minute. The On light flashes throughout the cleaning cycle and stays on green when the cycle is finished. Caution:
Never turn off the Epson Stylus NX110 Series during a cleaning cycle or you may damage it. 4. Run a nozzle check to confirm that the print head is clean. You may need to clean the print head up to 4 times. You can also turn off the Epson Stylus NX110 Series and wait at least 6 hours. Then try printing again.