Question about Jandy LXI 250 NATURAL GAS POOL HEATER -

1 Answer

Brand New out of the box Jandy LXI 250 NG. Fault check ignition control. where do I start? Plumbed myself and had a sparky wire it up.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Well sounds like a Engeneering. Most Engeneers can't figure out how to open the box without a drawing

Posted on Nov 19, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

"fault check ignition control

turn heater off then turn back on make sure gas is on

Jan 04, 2014 | Jandy LXI 300 PROPANE POOL HEATER -

1 Answer

No power to pool heater

make sure wiring is correct then make sure breaker is on

Oct 08, 2012 | Jandy LXi Pool Heater Lxi-250 Propane

1 Answer

My brand new pool heater reads no flow on its second day of use?????

check your filters if ok check wires to pressure switch if ok check copper tube

May 27, 2012 | Jandy LXI 300 PROPANE POOL HEATER -

1 Answer

Ignition fault LXI pool heater 400k

if ignitor is working try to adjust air damper make sure gas pressure is ok

Apr 12, 2012 | Jandy LXI 400 NATURAL GAS POOL HEATER -

1 Answer

New jandy LxI 400 natural gas pool heater makes a howlering sound which starts after it runs for about five minutes. The noise starts soft and continues to get louder. The noise is loud. Once I shut the...

Your bypass valve is bad. Probably because you did not pay attention to your water chemistry. It is located where the pipes enter the heater. You remove it from the side of the manifold that is outside the heater. It is not a difficult job. Just make sure your pump does not come on while the heater manifold is open!

Apr 16, 2011 | Jandy LXI 400 NATURAL GAS POOL HEATER -

1 Answer

Laars Lite 2 NG 250 Btu is the link for the manual to your heater. This may help, if not repost and I will see what I can do.

Jul 03, 2009 | Jandy Laars Lite2 Lg 125,000 Btu Heater

1 Answer

Won't ignite

make sure wiring is correct for 220 vs 110 wired for 220 from factory if 110 see inside panel move wires ignitor is not getting hot enough

Jun 02, 2009 | Jandy LXI 400 NATURAL GAS POOL HEATER -

Not finding what you are looking for?

526 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

8686 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Jay Finke
Jay Finke

Level 3 Expert

1384 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides