Question about Philips 42PFP5332D 42 in. Plasma Television

1 Answer

Power Problem Philips 42PFP5332D/37 power problem. The set blue light comes on, then then standby light comes on and flashes. no picture, no sound and no help from philips. Anyone knows the cause and possible solution? Help

Posted by on

  • 1 more comment 
  • donnadonnaca Dec 06, 2008

    ive the same problem on this plasma, turn it on comes into standby , press to power on and the standby flashes blue quickly,then back to red/orange flashes twice, then keeps lit,then flashes twice , help im based in liverpool ive a spare board what was ok but when put in this tv it was dead, no ive this one and it flashes

  • Anonymous Feb 26, 2009

    WHEN I TURN THE T V ON ,THE GREEN LIGHT COMES ON THEN AFTER ABOUT 5 SECONDS ,THE GREEN LIGHT GOES OUT AND A RED LIGHT COMES ON AND STARTS FLASHING. I UNPLUGGED THE UNIT AND REPEATEDLY FOR ABOUT A HALF HOUR AND AMAZINGLY IT DID COME ON AND REMAINED ON FOR A WEEK. NOW I'M BACK TO SQUARE ONE. HELP ME!

  • Anonymous Apr 18, 2009

    The power comes on and after about 5 sec the power shuts off and the red led light flashes 7 times, and will not work.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 52 Answers

Usually blink code on front gives direction but first thing to do would be to determine if surrounding sustain boards are causing draw on power supply by disconnecting them one at a time from power supply. y is on left looking from back and x is on right looking from back. if led goes solid with either board disconnected check supply voltages and if come up and stay up replace that board. if no change then you would need to verify vs on command coming from logic main to power supply. should be labeled on power supply connector and should be 3 volts. if present replace power supply if not present verify if logic main board sitting underneath signal board has one solid and one blinking led on if verifying normal operation and if so replace small signal board

Posted on Aug 19, 2008

2 Suggested Answers

  • 52 Answers

SOURCE: Power Problems - won't turn on

first thing to do is determine if there is a blink code as that gives a direction for t/s. regardless, what you should do first is offload the y main and x main sustain boards from power supply one at a time as there is a common issue where these boards can cause load on power supply and if voltages come up with either one offloaded that board should be replaced before proceeding. if y main is the issue there is an upper and lower buffer board to left of that board and also should be replaced at same time as 3 boards complete a circuit and replacing one could cause damage to others.

Posted on Aug 18, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Philips model: 42PFP5332D/37 The other day it clicked and the picture went out. The blue light comes on and it stays blue with no picture or sound


Your set need a thorough check-up. Contact the authorized service centre or an experienced service technician. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Oct 14, 2015 | Philips 42PFP5332D 42 in. Plasma...

1 Answer

Blinking blue light on my philips 60pl9200d/37


I see so many here with no sound/nopicture issues:

ISSUES:

1. IF sound main fuse/s are good.
2. If no power or standby check main fuse, standby power supply and any signsof damage you can see---burnt parts etc.
3. almost all these sets the troubleshooting involves checking voltages on the main power board to narrow down theproblem.
4. Be safe and if you do not know what you are doing don't open the set.

Answers to issues:

1. RE:fuses---if a blown fuse is found get a good replacement(not the genericones like Radio Shack). Many fuses are special even aside from amperage--Don'tput a higher rated amperage fuse in the set for any reason.

2. RE: power supply in set: if total dead aside from main fuse the set uses astandby power supply that runs 7/24 and a main supply (some are combined andsome not.

Here aside from checking fuses you want to examine all the filter caps on thepower/standby to see if any are puffed up or buldged up in some fashion--Iattach a photo of a good one---top should be silver metal and PERFECTLY flatand have no brown material coming out on top or bottom.

What happens in the standby area is they use caps with too low a voltage rating(saves money) which causes them to fail in a year or two---the standby runs7/24 and the heat dries out the caps and they fail.

3. Trouble shooting consists of the above and then at some point you have to buyand try a board to see if it fixes it or not.

4. Safety first--no TV set is worth getting injured or even killed over.If set is opened at least look for puffed up and bad caps like in thisphoto.6_7_2012_5_03_18_pm.jpg6_7_2012_5_03_35_pm.jpg

Jun 07, 2012 | Philips 60PL9200D-37 genie bulb only

1 Answer

My philips 42pfp5332d/37 when i turn it on the blue light comes on and it has no picture and just makes a clicking noise. If you look at the back you can see 2 green lights go on and off. it happened after...


Power supply board is dead.Replaced the power supply board,that the board where the power a/c cord go into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Jun 06, 2010 | Philips 42PFP5332D 42 in. Plasma...

1 Answer

I have a 42pfp5332d/37 plasma tv. I can not turn it on using the remote controller, however when plugged to the AC power source the blue light on the bottom left corner comes on and the screen is black and...


U know basic electronic's and soldering?Take ur tv aparts,where the A/C cord goes that power supply board.Searches all around the power supply board and it supporting boards.Look for these defective parts call capacitors,these capacitors have lekages of gases in one or two years of the tv in used,they alway bulges up it top,puff up it top.These capacitors are dead,replaced them u will stop hearing cliking,and have ur tv power back.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

May 07, 2010 | Philips 42PFP5332D 42 in. Plasma...

2 Answers

Philips 42 plasma tv. Blue light but no pitcure or sound


it is the bulbs inside the tv you can get them replaced and it should work

Jul 01, 2009 | Philips 42PFP5332D 42 in. Plasma...

1 Answer

Hi thanks for replying


The clicks you are referring to sound like High Voltage Leaks or Arcing. While it is clicking check for sparks around the high voltage transformer only with your eyes from a distance. If you see sparks shut it off immediately.

Dec 29, 2008 | Philips 42PFP5332D 42 in. Plasma...

1 Answer

Power Problems - won't turn on


first thing to do is determine if there is a blink code as that gives a direction for t/s. regardless, what you should do first is offload the y main and x main sustain boards from power supply one at a time as there is a common issue where these boards can cause load on power supply and if voltages come up with either one offloaded that board should be replaced before proceeding. if y main is the issue there is an upper and lower buffer board to left of that board and also should be replaced at same time as 3 boards complete a circuit and replacing one could cause damage to others.

Aug 15, 2008 | Philips 42PFP5332D 42 in. Plasma...

1 Answer

42 plasma tv model42mf230a/37 blue light on no picture no sound


with solid blue led set could be still powering on but would need to verify by checking power supply voltages. if up and signal is present with no menu or audio would be ssb as audio amplifier, micro processor and eeprom are on that board. if voltages are not present you need to offload x and y sustain boards one at a time from power supply and check voltages and if vs comes up with either board disconnected replace that board

Jul 25, 2008 | Philips Magnavox 42MF521D/37 Television

2 Answers

Philips Problem


Philips 42PFP5332D/37 power problem.
The set blue light comes on, then then standby light comes on and flashes. no picture, no sound and no help from philips. Anyone knows the cause and possible solution? Help

Jul 23, 2008 | Philips 42PFP5332D 42 in. Plasma...

Not finding what you are looking for?
Philips 42PFP5332D 42 in. Plasma Television Logo

584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71126 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...