Question about Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Red light stays lite and nothing works

My last wash was fine, but now the red light on the door will not go off and therefore I can not get the machine to turn back on. None of the button work.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Probably the red light indicates your drying cycle, and it has not completed it. Close the door and let it finish.

Posted on Aug 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

24" builtin Frigidaire Dishwasher, light on top of door says, Hold to lock. I can not operate the machine while this lite is on.?


Hello Ray E. Weaver - Sounds like the Child Lock option may have been selected. This is a safety feature that allows you to lock and unlock the controls to keep children from interfering with the wash cycle etc. Press and hold the AIR DRY pad button for 3 seconds while the door is latched. This should unlock the control pad for you, light goes out and the unit will display the last cycle ran. However, if it does not, try resetting the unit by unplugging it for flipping the household circuit breaker off. Wait approximately ten minutes and turn the unit back on. However, if it proves to be ineffective I recommend contacting a professional to assist further. The dishwasher may possibly have faulty door lock switch.

Apr 03, 2013 | Frigidaire Dishwashers

2 Answers

I have a Kenmore elite dishwasher. The Pots and Pans red light is flashing and the Heated Dry light is solid red. Nothing I do will change that. I've tried pushing any combination of buttons and ...


Hi


If clean light is blinking then it may be an issue with heater circuit, door switch or wash pump, please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset. If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back if you need more information.


Daniel

Jun 19, 2011 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Kenmore quietguard standard wont start.


is there any function at all? if not, check thermal fuse located inside near control panel, check www.searspartsdirect.com and enter your model # to show how to take it apart. If it has functional display lights, replace main control board after ohm test on wash motor and fill valve.

Jun 25, 2009 | Dishwashers

1 Answer

My KitchenAid Superba won't run, no lights, nothing


turn off the power at the breaker and let it stay off for at least one hour

Dec 17, 2008 | Dishwashers

1 Answer

Kitchenaid dishwasher woudl not work MOD KUDPO1FLWH6


is it on steady??? or blinking??? if on steady try pressing nad holding the button with the "lock" symbol on/or above it, thinknits the heat button, for 3 secs it will "unlock" the controls, if blinkin then its a diff issue, may be a bad door switch not recognizing hte door being closed therefore wont start,

Dec 02, 2008 | Dishwashers

1 Answer

HELP WITH NON FUNCTIONING DISHWASHER


similar problems here, repair man says its fine but the salt light was on so i added salt and works ok now. Some dishwashers don't function properly without the salt and rinse aid, even though you're pills may have then included, you still have to add them seperately, dumb but necessary at times.

Feb 27, 2008 | Dishwashers

4 Answers

Belling dishwasher IDW604


there is a small plastic catch in the door side of lock which loks arround the bar on the washer side of the lock somtimes it stays in you can click it out with a knife or simillar sould work fine after that

Dec 21, 2007 | Belling 24 in. IDW603 Built-in Dishwasher

22 Answers

Kenmore elite dishwasher


press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode. the test mode will stop the light from blinking and you can use the dishwasher again

Nov 27, 2007 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Dishwasher sticking half way through cycle


Crawlmom, it sounds like your door latch assy. and switches are not making properly sometime during the wash. Therefore the two dashes. You want to make sure that the dishwasher is level and securely mounted. Another thing is, on this model, if a key pad is stuck, the dishwasher will stop and flash the stuck key. Im not sure where the red light is coming from. Without being there, I'm leaning on the door switch assy. Check this out first and post back. Catriver.

Apr 15, 2007 | Kenmore 24 in. 16939 Built-in Dishwasher

1 Answer

Cranky dishwasher


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the switches. The heating element runs through the neutral side of switches, therefor if the switch is broken or the latch is not making, no heating of the water. This results in a default or very long wash time. Check this out first....Catriver..post back.

Oct 15, 2006 | KitchenAid KUDS24SE Built-in Dishwasher

Not finding what you are looking for?
Kenmore 24 in. 15932 Built-in Dishwasher Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...