Question about Phil & Teds E3 Jogger

1 Answer

Connections i have just been given the e3 red stroller and would like to place the child seat on top but dosnt seem to have the connection to do this,am i able to buy this from some where cheers if you can help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Got to practical pushchairs, online store thay do loads of spare parts for the phil and teds bugy and at reasonable prices, plus only 3.99 to post them to you, hope this helps

Posted on Aug 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a e3 v2 that was given to me by a friend but the brake is broken how do i replace it?


contact www.buggypitstop.co.uk they repair, and service all brands including Phil n ted they also doa valeting job to clean second hand pushchairs.

May 19, 2010 | Phil & Teds E3 - Charcoal Black Jogger...

1 Answer

Hi, I've lost the fittings to allow me to connect the Twin seat to the top of the buggy to use with the under seat fully reclined with the cocoon. Where can I purchase spare fittings from ?


Hi,

It sounds like the parts you need are the Elbow Hinges. If you contact Out n About (if in the UK) you should be able to get the parts.

I hope this helps.

Sep 14, 2009 | Phil & Teds E3 Jogger

3 Answers

How does the infant car seat connect to the stroller


It goes in the front seat it will click in place on the top of carseat connector that came with the stroller.

Aug 30, 2009 | Baby Trend Sit N Stand LX-7300 Travel...

1 Answer

Was given to me without the manual. Can't attach infant seat to stroller. Not sure how to do it.


The manual on how to do this can be found at www.babytrend.com.

To attach the Baby Trend Infant Car Seat, recline
the seat all the way back.
• Position the Infant Car Seat, facing toward the
rear of the jogger, so that the seat shell goes
into the Child Tray and latches into place.
(Fig. 13a) Check that the Infant Car Seat
is firmly locked onto the Child Tray before
using.
• Check that the front Child Tray is firmly
attached to the jogger's armrests. Make sure
that the car seat locks into the front Child Tray.
Then turn tabs on stroller frame to lock the
front of the car seat into the stroller. (Fig. 13b)
• To remove the Infant Car Seat, squeeze the
release handle located at the foot-end of the
seat and carefully lift upward on the seat.

Hopefully that helps!

Jun 15, 2009 | Baby Trend Expedition LE Jogger

2 Answers

Phill and Ted pram hood hard to put back in place


Hi,
I have the same problem with a Phil and Ted's Sport - but I believe I have the solution as below. This is taken straight from the Instruction Manual which you can view at: http://www.arango-design.com/Phil-Teds-Sport-Buggy-p/7890-0001.htm - towards bottom of page is a link to the instruction manual - which I was unable to get on the Phil and Teds website. Got this today but haven't tried it yet. Hope this helps.
Really becomes clear when you see the pictures in the instruction manual.
Regards, John
Hood
The sport hood is packed disconnected.
To reconnect:
1. Locate sun hood and hold it facing down, as shown ‘a’.
2. Insert crimped wire ends into frame, through eyelets, ‘b’.
3. Lay hood back (to top of buggy).
4. Locate red coloured pocket at top of fabric seat and insert rear hood wires into each side, ‘c’ and ‘d’.
5.Open hood and attach domes, at bottom of hood, to main seat, ‘e’.
6. Pull eyelet at top of hood over pegs on each side of frame, ‘f’
Note that the windows in the hood are lined with a sun mesh of
a lower shade factor than buggy fabric. Always use sun cream
and clothing for protection of children in direct sunlight.

Nov 12, 2008 | Phil & Teds E3 Jogger

2 Answers

Reclining back problem


I'm having the same problem. It's very frustrating.

Dec 05, 2007 | Peg Perego Aria OH - Free Style Mint...

3 Answers

Car Seat Installation on Stroller


There should be a tube with red ends that fits into a bracket when not in use below the pushing handle of the stroller. This is removed & put into place where there are two holes to this effect on the sides of where the child would sit when there is no car seat on top. The car seat should then "click" into postion when pushed down on the tube.

Apr 27, 2007 | Eddie Bauer Lightweight Travel System...

Not finding what you are looking for?
Phil & Teds E3 Jogger Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Phil & Teds Baby Gear Experts

Jennifer Rock
Jennifer Rock

Level 2 Expert

105 Answers

Kerrie Jager
Kerrie Jager

Level 2 Expert

45 Answers

ray gallant

Level 3 Expert

37793 Answers

Are you a Phil & Teds Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...