Question about Garden

1 Answer

My B&S 1150 Series (Model150000?) 249cc motor which drives a chipper starts on first or second pull when cold and runs great. But after running long enough to reach normal operating temp and then shutting down (ie. to empty chipper bag) it is impossible to restart. Bought this unit used and has Champion QC12YC plug in it. My first thought is to install a new plug but I can not find the specified plug type in my manual. Two questions, first what do you think is the problem and second what is the specified plug type/number (and gap) for this engine? Many thanks for your prompt reply. Eugene Stewart

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 202 Answers

Posted on May 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Real up and reving in park fast idle in drive


motor revving - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusDec 28, 2012 - motor revving - Sometimes the motor revves up and the light go dim on... If in park it takes alot of rev. to make the pop sound. ... 1996 chrysler cirrus change a bad fuel injector and now the engine revs ... Used Nissan Quest".

Idle issues... cold runs great... after warms up it hesitates ...

forums.nicoclub.com/idle-issues-cold-runs-great-after-warms-up-it-hesita...
Feb 20, 2009 - TYC 800107P Nissan Altima Replacement Cabin Air Filter ... when i go to park the car and throw it in park it goes up to like about .... If I leave it in drive when the idling starts to hesitate it tends to make the car jump forward.

All Questions and Answers for Nissan Repair - AllExperts.com

en.allexperts.com > Autos > Auto Repair

Jan 13, 2016 | 1996 Nissan Quest

1 Answer

When pulling away in my ford fiesta its doesnt want to go


Do you have any preventative maintenance done a couple
times a year or any testing done or just wait until it doesn't
run correctly,that is your problem with the car.

You can't start a car & drive away 30 seconds later

It runs off the computer until warmed up & you have very little
fuel control when cold

Nov 19, 2012 | Ford Cars & Trucks

1 Answer

Difficult to start chipper while gears engaged


The drive belt may be the wrong size if there is no play in the clutch. I have a 10 hp, but there is a common manual for the 10 and 8. My belt is a 4L380.

Jul 12, 2009 | Troy-Bilt Chipper Shredder

1 Answer

Hi I have 2000 BMW 320i. Lumpy idle when cold and oil light for


Your oil is a little low, and the timing may be off a bit but if it smooths out after warm it is probably ljust
low oil.

Jun 29, 2009 | 2000 BMW 3 Series

1 Answer

10 hp Troy Built chipper pull start frozen


If a branch was already being chipped when it ran out of gas...you must clear the hopper of any chunks of wood in it. Pull the plug wire and use a metal pry bar to dislodge any pieces of wood. when the flywheel runs free, put the plug wire back on and the choke on. Try it now!!!

Jun 14, 2009 | Troy-Bilt® Briggs and Stratton Chipper

3 Answers

MTD yardman chipper wont start get spark need manual


I am successful too at using the starting fluid in the carb or directly into the clinder. That is how I start my MTD 5.5hp chipper. My problem is I have to hold down the primer bulb to keep it running. If not, the engine will stall.

May 12, 2009 | Troy Bilt Walk Behind...

1 Answer

Chipper won't start


what engine do you have im guessing a briggs & stratton was it running previously or sitting awhile it can be a few things the flywheel key could be sheered or the points are bad or the flywheel & coil are rusted check flywheel & coil to see if rusted if so take coil off mild sand paper like 80 grit i beleave clean both to get the right gap between flywheel & coil turn the flywheel alittle bit so the magnets won't touch coil or if coil still of set flywheel to where it will touch magnets fat peice of sand paper not folded but flat sand paper about .020 gap between magnet & coil if you place sand paper against the flywheel magnet then set coil against sand paper & magnet that should give you 0.020 gap & it should start if not e-mail me i will guide you through everything to get it started

May 11, 2009 | Heavy Machinery

1 Answer

Troy-Bilt Chipper Shredder won't start


It takes good gas, good spark, and good air for a gasoline engine to run well. The next thing I would do is put a new air filter in it.

Apr 23, 2009 | Troy-Bilt® Briggs and Stratton Chipper

Not finding what you are looking for?
Garden Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

11064 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...