Question about Hotpoint Microwave Ovens

1 Answer

My et7424 induction hob comes on, then goes through some sort of programme with flasing lights and then all zones light up with three dashes - then you cannot turn the hob back on. Please help.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you resolve this issue with your hob as I have the same problem?

Posted on Jun 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have purchased prestige induction stove before an Year.The induction cooktop has a warenty for 1 year. With in an year we have got an issue with the functioning.The problem was , when we plug in and...


Make some letter with strong emphasy about some demand for them, if NOT proceed according to the law, send a copy to your personal lawyer, to the community, to the consumer association, etc .This procedure will give them FEAR to difamate.
God bless you

Oct 28, 2013 | Microwave Ovens

1 Answer

Prestige induction


There may be an electrical issue causing the unit to lose its electrical insulation in time. This may as well be due to the heat.
A heat shrink tube -providing insulation- facing too much heat may may have melted.
If non of the above, try plugging in the other way -if possible, for European plugs, that is possible-. Or replace your faulty fuse / residual-current circuit breaker (RCCB)

Oct 28, 2013 | Microwave Ovens

1 Answer

Aeg glass induction hob error code ER 21


reset the microwave. Disconnect the power cord, by 1minutes, and try again,the microcontroller is confuse.
If the problem persist you can be problem with the main controller board, repllace, but read your owner manual section troubleshooting for identi the error. download from www.retrevo.com
God bless you

Oct 27, 2013 | Microwave Ovens

1 Answer

Code e on only two of the right hand zones on siemens induction hob


Hello.

These codes mean that the oven's electronic control hasdetected a condition it needs to check which mean error. When you see a code,follow these steps to solve the problem:
  • Press "Stop/Clear" to clear the display and stop the beeping.
  • Reprogram the oven.
  • If the code still displays, turn off the power to the oven at your breaker box and wait five minutes before turning it back on.
Thanks.

Sep 07, 2011 | Microwave Ovens

2 Answers

I have a Brandt induction cooktop and 2 hotplates don't work at all and the other 2 now don't appear to be connecting with the saucepan. Heat light starts to flash then turns off completely. Unable to...


Sounds like a wiring problem,take off of course with no power and check it out. No harm if no power,and replace wire and or componet with same.

Jan 11, 2011 | Brandt Microwave Ovens

1 Answer

Hi, got old Eurolec Gas oven/hob. Hob lights up fine. Was cooking in oven all morning, no probs. Tried to light oven for evening meal & gas will not stay lit, goes out once ignitor & temp' dial...


Hi, your thermocouple is faulty, it is the little probe like thingy that sticks up into the pilot flame. It is there for safety purposes, detects flame and holds a valve open magnetically to allow the gas to pass through. Try giving it a clean with a scourer, sometimes works, or your pilot flame is not big enough, could be low on gas or unit needs a service Kristian KJ Tech

Sep 15, 2010 | Microwave Ovens

1 Answer

When one of the gas hobs is on ,it does not burn with a blue flame but a more yellow one .also black soot forms under the burner plate.it is on lpg


Have to adjust the piolot lights for the amount of gas coming out. U have too much gas coming out(yellow flame). On older gas ranges, there was a small screw between the piolot light & burners that had to be adjusted. (if this is a older model) have to turn the screw just a little at a time, till ur flame returns to blue on ur burners. Hope this helps.

Sep 12, 2010 | Microwave Ovens

Not finding what you are looking for?
Microwave Ovens Logo

Related Topics:

674 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Microwave Ovens Experts

William Miller
William Miller

Level 3 Expert

9098 Answers

Jim Thurston

Level 3 Expert

672 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Hotpoint Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...