Question about Black & Decker 5700 Powershot Forward Action Stapler

2 Answers

How to replace spring - Black & Decker 5700 Powershot Forward Action Stapler

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Hope the following is clear if not write back and I'll try to clarify, if you look at the body of the stabler molded to the body there is a bump that is round on the botton and kinda notched on top. the round part of the spring fits around the bump. The spring has a straight side and bent side. the straight side rests against the a flat bump which is slight back and lower than the round bump. the bent side clips into the notch on the handle (clip this end in last) I used a plier but there is very little tension involved the spring just returns the handle to the at rest position,

Posted on Oct 31, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Rexel Odyssey heavy duty stapler: The pring that pushes the staples into position can come losse if the stapler iss dropped. It's difficult to work out how to replace it! However, there are only two "lugs" that will take the circular ends of the spring. One obviously fits to the sliding staple retainer. The other to the back end of the pressed-metal inner body. However, to work, the spring must be threaded from this point along the pressed metal parallel-sided inner body over a rounded bent piece (shiny from prvious friction) and back down to the sliding staple retainer. It's trickey to do, but that's where it has to go in order to provide forward tension when the Stapler is closed.

Posted on Aug 02, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a spring for my saw ?


How to Replace the Pivot Spring on a DeWALT DW708 ...

? 6:48
https://www.youtube.com/watch?v=xz3EPWHjj0A
Aug 9, 2012 - Uploaded by eReplacementParts.com
Dammaged pivot springs can prevent your saw's cutting head from staying upright and, as a result, cause a ...

Replacement Parts ' Pruners ' Loppers ' Saw Blades ...

coronatoolsusa.com/replacement-parts.html
Items 1 - 12 of 268 - $0.00 (0 Item). You have no items in your shopping cart. MyAccount · Login ... Spring for AG 4980SS. 4980-5. $8.53. Spring. 6310-5C. $7.11 ...
Shop for Where can I get a spring... on GoogleRecoil Starter Spring Homeli...$10.00eBaySpring Starter Chainsaw Ech...$4.99eBayHomelite 26lcs, 5?20, 5?30n, 6...$24.00eBayMcculloch Chainsaw Spr...$13.99eBay5x Husqvarna 362, 365, 371...$19.75BonanzaSearch ResultsHow to rewind a pullstart spring - YouTube? 5:05https://www.youtube.com/watch?v=qTcL3_3leTkMar 13, 2010 - Uploaded by lenniepincherIf you ever need to rewind a un coiled pullstart spring. This might help you. It took me ... First pull of my chain ...Chainsaw Rewind Spring Replacement - Echo ... - YouTube? 3:38https://www.youtube.com/watch?v=oqcjL7W0XMAFeb 18, 2013 - Uploaded by RepairClinic.comThis video provides step-by-step instructions for replacing the rewind spring on Echo chainsaws. The most ...

Dec 12, 2015 | Garden

Tip

Replacing a Spring Pulley on Stairmaster 4000PT Stepper


Stairmaster Stepper 4000PT Spring Pulley Replacement
  1. Remove the bottom cover.
  2. Unhook the pedal arm return spring from the spring hanger.
  3. Remove the snap ring from th pulley shaft. WARNING: To reduce the risk of eye injury, wear eye protection when removing snap rings.
  4. Slide pulley and washer off the shaft.
  5. Before reinstalling the pulley, clean the pulley shaft thoroughly with a clean, dry cloth. Apply a thin coat of multipurpose grease to the pulley shaft.
  6. Slide the pulley and washer onto the shaft. Install the snap ring.
  7. Route the spring under the spring pulley.
  8. Hook the end of the spring over the spring hanger. WARNING: Do not twist the spring during installation. It will wear excessively and reduce the life of the spring.
  9. Reinstall the cover.

How To Replace Spring Pulley on Stairmaster 4000PT

on Mar 10, 2015 | Stairmaster 4000PT Stepper

Tip

Replacing a Pedal Arm Return Spring on the Stairmaster 4000PT Stepper How To...


Replacing a Pedal Arm Return Spring on the Stairmaster 4000PT Stepper

How To Replace a Spring on Stairmaster 4000PT
  1. Remove bottom cover.
  2. Unhook the pedal arm return spring from the spring hanger.
  3. Detach the spring from the step chain by removing the master link. The spring-chain connector is in good condition if it has an hour glass shape. Replace a worn spring-chain connector.
  4. Check to ensure that the spring pulley turns freely and is not worn excessively. Refer to the "Spring Pulley" section if you have to replace the pulley.
  5. To reinstall th spring, connect it to the end of the step chain using the master link.
  6. Route the spring under the spring pulley.
  7. Hook the end of the pedal arm return spring onto the spring hanger. WARNING: Do not twist the spring during installation. It will wear excessively and reduce the life of the spring.
How to Replace Pedal Arm Return Spring on Stairmaster 4000PT

on Mar 10, 2015 | Stairmaster 4000PT Stepper

1 Answer

Change springs on garage door


It's is straight forward. Select a replacement spring with the same tension color as the original spring. The color is applied to one of the hooks. Above all thread the safety wire through the center of the spring.

Feb 02, 2014 | Stanley Hardware 730610 110 Lb Garage Door...

1 Answer

Replacing rear coil springs


You have to remove the struts from the car. Place the struts on a compression tower to relief pressure from spring. Once spring is compressed take of the top bolt on the strut which holds on the strut mount. After strut mount nut is off, loosen the springs tension and replace it with the new coil spring you are planning one using. Tighten the spring with mount back on and tighten bolt. then reinstall on car.

Jun 15, 2013 | 2004 Honda Accord

2 Answers

Need to change kick start spring


Hi, i am sorry but you dont say what the model of your machine is, this would help me determing the correct, answers for your questions, most kickstart springs can be changed by simply removing the clutch cover followed by the kickstarter shaft and then replacing the spring, make a note of kickstart stop location carefully remove the shaft holding the gears together replace the spring followed by the. Replacing the shaft and tensioning the spring before cover replacment, oil,etc. Some machines the shaft and spring is inside the centre cases and a complete engine strip is ness

Sep 25, 2011 | kawasaki KX 250 Motorcycles

1 Answer

How difficult it is to replace front struts on a 2003 subaru legacy wagon? I have done shocks and many other car repairs, but this would be the first experience with struts. Anything to look out for...


  • 1 Raise and support the vehicle with safety stands. While the vehicle is raised, remove the wheel and tire. This will give you access to remove the two lower bolts and nuts from the strut. Remove the upper flange retaining bolts.

  • 2

    Slide the strut spring assembly out from the vehicle. Using a strut spring tool, collapse the spring. Remove the center nut, upper bearing flange assembly and collapsed spring. Discard the old strut and replace with new strut. Discard the upper nut and replace with new nut. Do not release the spring tool from the spring.

  • 3

    Install collapsed spring with tool in place onto the new strut. The spring does not need to be replaced unless it is broken. Be sure to note the position of the spring ends on the strut. Install upper bearing flange, making note of the position of the spring end on the flange. Install center nut and tighten to specs. Then remove the spring tool.

  • 4

    Put the completed strut and spring assembly back onto the vehicle. Tighten nuts and bolts to manufacturer specifications. Install the wheel and tire. Lower vehicle.

  • good luck
    yz-maniac......

    Oct 29, 2010 | 2003 Subaru Legacy

    1 Answer

    Do I need a spring compressor just to remove and replace the front left and right strut mounts on a 1997 pontiac grand prix gt?


    If your replacing it with a quick strut which is the spring,mount, and strut assembly then a spring compressor is not required.If replacing just the mounts then definitely a spring compressor is required. Please use extreme caution when compressing and removing strut assemblies as the springs maintain alot of pressure on them.

    May 20, 2010 | 1997 Pontiac Grand Prix

    3 Answers

    Rear springs replacement


    You will need a spring compressor first of all. You have to remove strut, compress sring to get cartridge and spring apart and then replace new spring on strut and replace into vehicle. This is a nasty job without a hoist

    Sep 24, 2009 | 1996 Pontiac Grand Am

    1 Answer

    Spring rusted off. How do I replace it?


    Make sure that where the spring attaches to the bottom of the tub mount, is not rusted into also. If it's not replace the spring. Here is how.
    Find where spring goes back to. Possession your self on the side where the spring Now from under the washer, pull the tub toward you (the place where the spring goes) Be ready to hook spring back up. If you cant get this to work, try laying the machine down so that the tub will fall toward the spring goes. This will mae it 100% easier to replace them.
    Please rate this solution

    Aug 28, 2009 | Kenmore Washing Machines

    Not finding what you are looking for?
    Black & Decker 5700 Powershot Forward Action Stapler Logo

    1,245 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Black & Decker Tools & Hardware - Others Experts

    Phil Rivera

    Level 2 Expert

    83 Answers

    Pieter Vleeshouwers
    Pieter Vleeshouwers

    Level 3 Expert

    1671 Answers

    john h

    Level 3 Expert

    8286 Answers

    Are you a Black & Decker Tool and Hardware - Other Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...