Question about Neff 24 in. S5456 Built-in Dishwasher

1 Answer

Hotpoint sdw dishwasher

Our dishwasher stopped mid cycle lights flashing now will not restart but is full of water

Posted by on

  • Esmman May 11, 2010

    I have the same problem. Could you please explain how we get to the drain pump and the drain hose. I have an integrated NEFF dishwasher. Do I have to pull the whole d/washer out of its position ? Thanks. Esmman

  • Anonymous Mar 16, 2014

    Hi dishwasher stops mid cycle lights go out then will restart after about 40mins

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It is possible drain pump blocked, you need to empty d/washer manually, check inside drain pump which is at end of drain hose, always isolate d/washer from power before attempting any work on it.

Posted on Oct 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Hotpoint SDW 60 problem! The dishwasher starts and goes through pre-wash but stops with just the 'Delicate' light flashing. Does anyone know what the problem may be?


If the original light flashing that means it indicate a fault in the heating circuit. Heater, wiring, thermistor / pcb. (Main control board).

The new flashing light, PreWash (this is the only one on my list for a fault code indication). indicates a fault with the thermistor.

You would need to check by taking the door apart that the thermistor hasn't come off it's mount by the dispenser.

You would then need access to and be able to use a multimeter to test the heater and wiring to ensure they are closed circuit.

Jul 09, 2011 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hello, my Haier dishwasher stopped mid cycle after about 10 mins and will not restart. the lights just flash and buzzer sounds. Can anyone help please?


Have the same problem with mine and have found no solution in the manual or web. four lights flashing and beebs ten times every ten seconds, water coming in and draining out constantly, very frustrating!

Jan 03, 2011 | Haier Dishwashers

1 Answer

Dishwasher starts to work but after 30 seconds stops and two lights start flashing on pannel


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.Service manual below, if the above doesn't help. http://appliancejunk.com/ge/dishwasher/31-9137.pdf

Jun 24, 2010 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

After drying there is water in filter trap is this normal


IF THE WATER IN PORTABLE DISHWASHER AT THE BOTTOM IS MORE THAN THE DRAIN HOSE FULL OF WATER THEN ASK WARRANTY PEOPLE. WHEN PUMPING WATER UP IT CAN ONLY PUMP SO MUCH WATER OUT OF HOSE BEFORE THE WATER DRAINS BACK INTO DISHWASHER.-- HOPE THIS HELPS

Mar 08, 2010 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

I have a hotpoint aquarius sdw60 with the eco 45 light flashing fast and will not reset I have tried turning off the power I have stripped the pump this was clear. then reinstalled it but it is still same


I have a Hotpoint Aquarius SDW 60 The delay 3hr &12hr lights are flashing at the same time. Machine won't start. If the door is slamed shut. It get stuck on the Fast & Prewash 40 degree cycle. and stays there.

Jul 13, 2009 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

Hotpoint SDW 60 dishwasher stopped working


The error code is for the 'heater circuit' before getting a new heater check the thermister (on the end of a black wire hanging off the main control board ) as the either dryjoints or comes loose

Dec 30, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

FDW40


This is a blocked pump,Strip down pump and remove blockage.

Jul 24, 2008 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Neff 24 in. S5456 Built-in Dishwasher Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Neff Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Stefano Andreani
Stefano Andreani

Level 2 Expert

69 Answers

Are you a Neff Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...