Question about Kenwood Kdc-x994 Car CD/ MP3 Player

1 Answer

How do i get my radio out of protect mode?ive tried everything even disconnected the whole thing and put it on another battery but still on prortect mode

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Kenwood Master
  • 2,226 Answers

You probably have a bad internal output ic.

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Radio code jeep grand cherokee


I have a kenwood KDC U353 car stereo and it has gone onto protect mode i have done everything it says in the manual and even taken it out of the car just in case it was damp i have tried putting it back in but still is in protect mode can anyone help me please

Jun 28, 2013 | Car Audio & Video

1 Answer

My hifonics bxi1210d amp goes to protect mode 2 seconds after turn on


Overdriving the output can cause it to go into protect mode. You will not be able to restore normal operation until failed components are replaced.

Jun 06, 2017 | Hifonics Car Audio & Video

3 Answers

My kenwood kvt 514 is in protect mode


It sounds like your amp is not grounded properly and is tryin to use your radio as a ground through the RCA's or there is a bad channel (dead short) in the amp.

Jun 02, 2009 | Car Audio & Video

3 Answers

Kenwood car stereo cd player reads protect mode how do i fix this


i have a kenwood kdc-241 car stereo and it has gone onto protect mode i have done everything it says in the manual and even taken it out of the car just in case it was damp i have tried putting it back in but still is in protect mode can anyone help me please

May 25, 2009 | Kenwood Car Audio & Video

1 Answer

Cd stock


You might wanna try taking the radio fuse out for a few seconds and then putting it back in. Sometimes that helps the radio reset itself and will begin working as it should. If that doesn't work, try disconnecting the battery also for a few seconds, and if still that doesn't work, then you might have to take the whole thing out (radio) and open it to try to take the CD out manually. After that, if the problem persists, just replace the whole thing. Hope that only taking the fuse out for a while will solve you problem.

Jan 13, 2009 | 2005 Chevrolet Malibu Maxx

1 Answer

Blackberry camera


turn off ur bb mobile by disconnection the battery from mobile phone and put the battery after 1 min and start the hand set

Nov 16, 2008 | AT&T Blackberry Curve 8300 Smartphone

2 Answers

LED Light is on, but no sound from sub at all.. Have double backed on all wires but still nothing! HELP!!


If you've overheated it a number of times, it's possible that you've damaged the amp and it's trying to protect itself even though it's too late. Try disconnecting the sub from the amp. If there's no change, then there's a problem within the amp. It could be a thermal switch or possibly a stressed amplifier module.

Hope this helps. Good Luck!!

Mar 21, 2008 | Car Audio & Video

8 Answers

Kenwood car stereo KDC-W3534 : warning message PROTECT


i had the same problem and i just disconnect the battery and and reconnect it and everything works fine!! try it

Dec 19, 2007 | Kenwood KSC-310CCS Center Channel Speaker...

1 Answer

Stuck in protect mode


Speakers shorted out, blew a fuse. Replace the unit or (cross your fingers and) open up the box and find the blown fuse.

Nov 23, 2007 | Sony STR-DE425 Receiver

3 Answers

Red LED "Protection Light is on" What is the problem


The red light means the amp is in protection mode. A few things can cause protection mode..... First disconnect the subs completely from the amp, and turn it on, if it powers up you have blown subs. Also try checking the main power wire at the battery...sometimes the current your meter is seeing is backfeeding from the remote wire, so your main power line could be blown at the fuse under the hood. hope this helps

Jul 17, 2007 | Crunch BlackMaxx BMX2250 2 Ch 1000W Amp...

Not finding what you are looking for?
Kenwood Kdc-x994 Car CD/ MP3 Player Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...