Yellow light flashes 6 times - Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

All questions need 'make model (what it is)' or it is all guesswork and clairvoyance 'Anonymous'.

A battery operated massage Chair, powered wheelchair? Give us a clue!

Google has some ideas and shows Questions here on Fixya. Blink Codes listed by make are readily available and are in your manual.

The power arm is flashing a wrench and it blinks 8 times - Fixya

https://www.fixya.com > support > t14332970-power_a...Nov 14, 2019 - Turn the chair off, wait 5 seconds, turn the chair back. If chair still does not run and your wrench is flashing you have a problem.SOLVED: A wrench light is on the indicator and the chair - Fixya
Sep 9, 2019What does the wrench blinking mean on the wheelchair and ...
Oct 5, 2016
SOLVED: What do eight wrench flashes indicate? - Fixya
Dec 6, 2019
Pronto m51 electric wheelchair yellow wrench light blinks 8
Sep 5, 2019
More results from www.fixya.com

Sorry I don't have service info on this brand

How do you fix the power supply

Six flashes indicates the inner cover is open.
http://kbsupport.cusa.canon.com/system/selfservice.controller?CONFIGURATION=1011&PARTITION_ID=1&CMD=VIEW_ARTICLE&ARTICLE_ID=43030

I have a Miele Futura from about 2011. In 2019, I had the issue were all three yellow lights, cleaning, drying, and end, were flashing, initially after a cycle was running and later, after several resets, almost immediately after trying begin a cycle. I strongly suggest watching Scott the Fix It Guy on YouTube. He shows that there are basically 3 different reasons why. 1. A leak that is tripping the leak sensor. Put the dishwasher on buckets and watch for a leak without the drip pan. If no leak, check the motor. He shows how to remove and inspect. If there is something in the impeller it will trip those three flashing lights. I did that and found no blockages and that too didn't fix it. The final source is the heater / pressure switch. So I ordered that from Miele ($75) replaced it and now it runs great!!

bad sein pcb

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal

All the best Pineworks

Search Results for ORANGE 5 AND GREEN 1 <<Previous 30 results Next>>
1. Power light (or Alarm and Power lights) alternate(s) between orange and green
After long green flash, there are 2 or more alternating orange and green flashes. There may also be a Service Error message on the computer screen. 2. Alarm / Power light flashes orange 11 times consecutively (Automatic Print Head Alignment Error) 3. Alarm / Power light flashes orange 2 times consecutively (Load Paper / Paper Feed Error) 4. Alarm / Power light flashes orange 3 times consecutively (Paper Jam Error / Cover Error) 5. Alarm / Power light flashes orange 4 times consecutively (Out of Ink Error) 6. Alarm / Power light flashes orange 5 times consecutively (Print Head Error)
#1 & #6 seem to be as close as I can find:
here is the page (Below) if you just put the error in the space provided.

http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=257&modelid=10239

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal

If you are getting 6 beeps and the yellow light is flashing 6 times, it usually means that the waste tank is full. This is a large peice of sponge placed at the bottom of the case. It is difficult to get out and I am not aware of replacements being made available from Canon. You will need to wash it.

Durn