Question about Amana AKS3040 Gas Cooktop

Open Question

I am trying to open the unit to replace the module. How do I do this

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Middle section ticking sound with sparking as if trying to ignite even though knobs aa


see this steps and fix it. God bless yo
Relight an oven pilot:
  1. Turn all controls off, open the doors, and allow gas to dissipate.
  2. Hold a lighted match near the tip of the pilot on the burner assembly. If a burner does not light within two minutes, adjust the pilot, step 3.
  3. Turn the pilot adjustment screw (located near the pilot or the thermostat) in small increments and retest until the pilot has a blue flame.
  4. Check and replace an oven spark igniter:
  5. Turn all of the appliance controls off.
  6. Open the door and remove the oven bottom and the baffle (see above).
  7. Unscrew the igniter from its mounting bracket and inspect it for cracks or other defects. Replace it if it is damaged.
  8. To replace a faulty igniter, find the ignition control module, unscrew the cover, and disconnect the module. Install the replacement part and test.

Oct 02, 2012 | Fisher and Paykel GC36 Gas Cooktop

Tip

Fault Codes Kitchen Aid cooktop


F03 One or more eyes permanently pressed. Recommend that the glas be cleaned and all objects removed.<br /> Unplug the unit for one minute the plug back in if the error still remains after returning power then you will need to replace the touch control module.<br /> <br /> F12 Electronic board and touch module communication error.Unplug the unit for a couple of minutes.Restore the power if the error return then you will need to replace the board connection cable between the touch control module and electronic control. if the error remains replac ethe electronic control board. If the error comes back again replace the the touch pad.<br /> <br /> F13 Internal CPU checksum error.Recommend you replace the touch control module.<br /> <br /> F22 Key sensitivity problem.Turn power off to unit for a few minutes,if the error returns after power is restored replace the touch control module<br /> <br /> F36 Temperature probe hardware error.Recommend that you replace the touch control module.

on Jan 02, 2011 | KitchenAid 36 in. KECC568 Electric Cooktop

2 Answers

The ignitor keeps sparking and won't stop.Do not


First of all, the model number is under the cooktop bottom, and secondly, this can happen due to the burner switches got wet somehow. Best thing to do is to unplug unit for 6-12 hours, allow to dry, then re-plug unit back in, this should be enough time to dry out the burner switches.
Good luck

Jul 13, 2011 | Bosch Cooktops

1 Answer

Piezo igniter won't quit


Possible stuck burner switch or failed spark module. Unplug unit. Remove wires from burner switches at module and plug back in. If it starts sparking, replace module. If it stops, then replace switch harness.

Jan 18, 2011 | GE 30 in. Profile JGP932 Gas Cooktop

1 Answer

I need to replace two blue indicator lights and I need directions


I have replaced several of the indicator lights in the control knobs.

Turns out that Dacor doesn't sell exact replacement lights (actually LED modules).

What I did was to go to a local electronics supply store and purchase Blue replacement LEDs and a current limiting resistor to connect in series. Replacement LEDs can vary in brightness depending on your taste ... I chose a super bright LED which makes the control knobs noticeably brighter. The value of resistor will vary depending on the LED you choose (brighter LEDs need slightly more current and as such the resistor value will be slightly less).

Once you've opened the range from the top (remove knobs, grates and burners) then remove a few screws and the entire unit opens with a hinge in the back.
Look over the LED light modules which shine just below each knob and fashion a replacement LED assembly.

Total material cost per LED unit was ~ $2-3 (LED, resistor, wire and heat-shrink tubing)

Jan 04, 2011 | Dacor 36 in.PGM365 Gas Cooktop

2 Answers

I have a Dacor electric ceran topped cooktop, model ECC46S. One of the ceran glass tops is cracked badly. I have searched everywhere for either a complete module, EM4LFB with no results. I probably...


Sorry to read about your problem, I hope this helps you out.

you might want a new unit, glass replacement will cost from $600.00 to $900.00 and thats just for the glass

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

Dec 20, 2010 | Dacor Cooktops

1 Answer

All cook top burners spark when any is turned on


OK, the best action is to call for service, if the unit was just installed, and purchased. This unit should be covered at this time, by the manufactures warranty, or store 30 day warranty. This repair should be free. The culprit will be a faulty spark ignition switch, and module. Testing is required. Once this switch, or(module), is replaced, the unit will operate correctly.

Nov 04, 2009 | Jenn-Air JGC8430 Gas Cooktop

2 Answers

Recived spark module for 6 burner gas stove on DCS gas oven/


I want to gas geyser using sparking unit (ckt Diagram)

Feb 28, 2009 | DCS Cooktops

3 Answers

Viking Gas Cooktop - Ignition sparks continuously when in 'on' position


This is likely caused by either a dirty ignition electrode, a cracked ignition electrode, or a bad spark re-ignition module.

Clean and inspect the six electrodes for cracks, If that doesn't solve it order a new
Ignition module from an internet appliance dealer that carries Viking parts like Appliance Zone.

If you replace the Ignition module yourself, make sure to turn off the circuit breaker to the range/cooktop before you work on it. Also, make a drawing of where the different color leads are plugged into the ignition module before you unplug the wires and plug them into the new re-ignitor. If the unit is under one year, this should be covered under the warranty.
Viking had a recall a few years back on their ignitor modules.

Jun 03, 2008 | Cooktops

2 Answers

Burners not lighting


I had the same issue and replaced the spark module myself, lots of wires and you have to make sure to label them before removal to be able to hook them back up correctly. To get to the module you need to unscrew all burners, no need to take the cover plate under the knobs. Burners remove by unscrewing center, brass nut. OEM spark module is VIKING RANGE #PA020021 U-67205-21. Go
od Luck

Apr 18, 2007 | Viking 37 in. VGSU161 Gas Cooktop

Not finding what you are looking for?
Amana AKS3040 Gas Cooktop Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Cooktops Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

paulcarew

Level 3 Expert

2458 Answers

Are you an Amana Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...