Question about ASUS Computers & Internet

1 Answer

G53SW-XN1 model notebook. Has green light and orange light for power and power button doesn't turn on, tried hard reset, Is there any type of solution, had 3 issues for same model today.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

That particular model has the power switch assembly located directly above your video card, which gets extremely hot. There is the possibility that the excessive heat may have damaged your power switch, causing the failure. I would recommend taking it in to have it checked out, or contacting Asus support for replacement/repair.

Posted on May 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

NEC lt240 lamp light stays off and power light is orange, no Image


COULD HAVE HOUR COUNT LAMP LOCKUP YOU WILL NEED TO RESET HOUR COUNTER BY USING BUTTON CONFIG AND MAINS.

john

www.jvsvisual.com

Apr 15, 2013 | NEC LT 240 Multimedia Projector

1 Answer

When I want to print it says error 6C10 switch off switch on. Doesn't work!


that indicates full waste ink pads/absorbers. to reset the counter try this:
1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power button.
(DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and
Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)
4) When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)according to the function listed in the table below. (Each time the Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

any way if the absorber/pad is full, it have to be cleaned!

Sep 20, 2011 | Canon PIXMA iP4600 Color InkJet Photo...

1 Answer

Error 27


Hello.
Here's what you need to do;

Make sure the printer is powered off but connected to a power source, then press the Power button while pressing and holding the Stop/ Reset button. And turn on, press the Stop/Reset button two times while pressing and holding the Power button. When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.


The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

Jun 17, 2011 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

Hello , I'm using Canon MP160 for windows XP bit 32 ... I can't scan or print ... The printer flashes E22 .. What should i do ? healp please .. thanks !


E22 means cartridge error
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

May 17, 2011 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

I cannot wake up my HP Pavilion dv3. blue power led flashes on and off and orange connection led too.


The display driver could have crashed, try holding the power button until the lights go off, and the hard drive powers down (you can hear the spinning stop) then try to power it back on. If that doesn't work, do a hard reset, which would be unplugging it from any AC power, and removing the battery and then reconnecting the battery before powering it on. Should this not work, i would say it's safe to assume the backlight is non functioning and a replacement would have to be ordered.

May 05, 2011 | HP Pavilion Dv3-1075us Notebook

1 Answer

Ink absorber full


What model is it?

General reset:

How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again

Dec 02, 2010 | Canon Office Equipment & Supplies

3 Answers

How to reset absober full mp198


PLEASE TRY THIS, Probably your waste ink counter. Should be cleaned or replaced before resetting but usually you can get away with resetting once.
1. Start with printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. press RESUME twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Select functions below with RESUME, execute with POWER

0 presses - green light - Test Print (exit service for i960)
1 press - orange light - EEPROM info print
2 presses - green light - EEPROM initialise
3 presses - orange light - reset waste ink counter

Feb 26, 2010 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Ink absorber is full.


Try this:
How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

May 01, 2009 | Canon PIXMA iP6310D InkJet Photo Printer

3 Answers

Canon mx310 wase ink full. Any ideas how to reset


How to clear E27 Waste ink absorber full
1.With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2. When the Power is lit, press the Stop/Reset button two times
while pressing and holding the Power button.
3. When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4. When the on/off lights in green, press the Stop/Reset button the
specified number of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

Note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print

2 times Green EEPROM print
3 times Orange EEPROM reset

4 times Green Waste ink counter reset
5.Turn off the printer.( it must be turn off) then turn it on again


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Apr 13, 2009 | Office Equipment & Supplies

2 Answers

My printer ink absober was full. my printer display e27 code. what can i do?


hi,
CANON PIXMA MP160 All-In-One InkJet Printer
has few common problems. Such as Driver CD lost, Scanner does not work, Connection problem etc. For find all these software solution just click here....
75aba9d.jpg3f22050.jpg

http://www.canon.com/printer/prob676ijt65/solution

prirweto-i-9

Apr 07, 2009 | Canon PIXMA MP160 All-In-One InkJet...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18390 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

David
David

Level 3 Expert

778 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...