Flashing light - video going out

Question edited for clarity, your television is 'Nordmende', not 'Norfmende'.

Time for a new one, but try the power reset first as mentioned here.

The standby light on my nordmende tv keeps flashing

JustAnswer https://www.justanswer.com > TV Problems
Sep 27, 2012 - Unfortunately, the symptoms you are experiencing (flashing power/status light, tv won't power on) are generally symptomatic of an internal ...
1 answer · Top answer: p0llinate : Hello, and welcome to justanswer, a pay site for expert technical help. My ...

How to fix my nordmende tv as blue light is flashing and ...

Ask Me Fast https://www.askmefast.com > How_to_fix_my_nordm...
Its the power supply board, capacitor(s) have gone. Solder on new or replace board. source: 26" lowry tv red and blue standby light flashing and tv wont turn on?

• 
  

  My nordmende tv model nmh077fhd blue light is flashing ...

  https://www.askmefast.com > My_nordmende_tv_mo...
  Normende tv red light wont come on Nordmende tv blue light flashing Nordmende ... said: nope. will turn on and work fine until the screen dims, goes black.

The flashing standby light on your Luxor TV can indicate several things, including:

1. Power supply issues: If the TV is not receiving proper power, the standby light will flash.
2. Malfunctioning hardware: A malfunctioning component in the TV such as the power supply, main board, or backlight system can cause the standby light to flash.
3. Overheating: If the TV is overheating, it will go into protection mode and the standby light will flash.
4. Software issues: A software glitch can also cause the TV to display a flashing standby light.

If the flashing standby light persists, it's best to unplug the TV, wait a few minutes, and then plug it back in. If the problem persists, you may need to contact the manufacturer or a professional repair service for further assistance.

Hello ? Is there any sound?

Take the screen off connect power and watch LEDs if any don't flash its LEDs only needed to change faulty strip if they all flash its probably t con boards.

Hi,
If standby red light is solid then press power or channel button on remote of tv itself to turn it ON.
And if red light is blinking/ flashing then it is an indication that tv got problem and tech visit is needed to sort out problem.
Thanks.

Technika flat 32 screen: Doesn't not switch on, the blue standby light just flashes.

I have the same thing with my tv standby button comes on red flashes green then back to red need answers can u help if u can plz thanks

Hi.

The TV stays in standby because protection circuit kicked in.

Protection kicks in when an internal fault had been detected.

In your case the SCART cable may have caused a short.

When on protection the TV will stay in standby, will not respond to buttons or remote, and will not start up.
All higher voltages from PSU get shut down by controller board, and only the +5V remains on.

To attempt resetting the TV, disconnect all video cables, disconnect the power cord, wait about one hour and plug it back.

If TV does not restart, then there may be an internal fault.

In that case leave TV unplugged for longer, just in case.

If still no luck, then call Sony to discuss a repair. The number is listed on your owner manual.

If instead TV will restart, do not use the faulty video cable again, this can damage your TV.

Regards

AKB 66 in self diagnostic test means...TV goes to standby (shut-off) for AKB problem 66 times. AKB is White-Balance signal and it is not proper or maintained in your TV. So error signal produced and TV goes to shut-down state.
Regardnig Standby button, its available on remote only. If you push TV Power switch, TV will switch ON, push it again to OFF TV. Power Button on remote set TV in standby status and you dont need to push power button of TV itself.

got the same here, turned it off via on/off button, then the big lightning storm happened ,next morning same as the rest, anyone got a clue how to fix it, ive opened it up but even thats beyond me.

Ant