Question about Samsung WF337AA Front Load Washer

2 Answers

Shook Violently first time on spin cycle

I just bought a Samsung Silvercare and it shook violently the first time on spin

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Make sure you take out the four shipping bolts on the back side or you will surely damage the tub and it will shake and vibrate terribly.

Jeff

Posted on Mar 12, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 706 Answers

Make sure the washer is leveled properly and all four feet are resting on the floor. If it is level, try running one cysle without any clothes in it to see it is spins without that violent shaking.. you may have also had an out of balance load.. Hope that helps!

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My brand new amana washer shakes violently when spinning


try adjusting the feet on the bottom of the washer the floor may not be level to adjust the legs turn them with a wrench or if the lock nuts are not tight turn the legs clockwise as you look at the front of the machine till all four feet are sung on all 4 corners. This is the most common problem. hope this helps and thanks for using fix-ya

Feb 15, 2010 | Washing Machines

1 Answer

Kenmore Oasis HE shakes violently during spin cycle


Machine legs should be adjusted so that machine is level and standing on all four legs. The load in the machine should be evenly distributed. Utube has an excellent video on washing machine repair.

Nov 20, 2009 | Kenmore Oasis HE 27082 Top Load Washer

3 Answers

Samsung P801 Front Loader shakes violently during spin cycle.


When the washer goes into spin cycle it is suppost to start at a slow speed and continue to increase speed (to a maximum of 800 RPM) as the water leaves the clothes. Your washer is going directly to 800 RPM which causes the washer to shake and stop giving you the E4 code. The control board that controls this speed increase must be replaced.

Feb 23, 2009 | Hotpoint Ultima WD72 Front Load...

2 Answers

Whirlpool washer LSQ9549LW makes one loud, violent clunk ea. spin


great analogy, sounds as if you have broken/stripped the tub block( its waht secures the inner tub to the outer tub) part number 389140, if you removethe agitator( a 7/16" bolt down the center of agitator) there is one more lock ring that isactually tightened down across the top of said "tub block"( usually need a specialty spanner wrench to remove, but have done it with a pipe wrench) after removing that lock nut the inner tub will release and the new tub block can be installed...

Feb 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Samsung Front Loader Washer Out of Control


make sure you take out the 4 srews in the back of the washer .
This is only to hold the drum in place when it is transported to you

Remove them and you should not have a problem.

This info is only for front loaded wahers and not dryers or top loaded washers

Mike T.
teolismike@sympatico.ca

Aug 13, 2008 | Samsung WF337AA Front Load Washer

4 Answers

Washer shakes violently and loudly during spin cycles


we had the same issue. however, it was solved by removing for big screws from the back of the machine. if you look you'll see 4 screws with yellow covers that need to be removed. this solved the issue instantly.

btw, frigidaire's help line SUX.

Feb 02, 2008 | Frigidaire Affinity ATF7000ES Front Load...

2 Answers

Repair front load washer


We've had that same problem since we bought ours 3 years ago...but it was intermittent, and we never knew when we'd get the spin-dry cycle to work. Sears made 10 service calls, and replaced everything in the machine except the motor and motor control board. Those two parts were ordered and delivered as a result of the 10th service call. Of course, when the service guy was here, the spin worked! After he left, the next load did not spin. Frustrated, I opened the front end and looked around. I had noticed how violently the drum shook while operating when the service guy was here, so I decided to see if the wiring harness from the motor might be loose where it plugs into another harness that must go to the motor control board. There was a definite tightening of that connection as I squeezed the two harness plugs together. (I tightly secured a plastic zip-tie around that connection to prevent it from vibrating loose again) Since then, I have had absolutely no problem with the washer. I called Sears and told them I had managed to solve this long-standing problem on my own, and how, and also told them to cancel the service call to install those parts I ordered, but to pick them up and reimburse me for them. (I never opened the two boxes that arrived) They did just that, and we finally have a washing machine we can rely upon to complete the wash like it's supposed to. It's been a very frustrating and expensive 3 years, but now all is well.

Dec 15, 2006 | Kenmore 43142 Front Load Washer

Not finding what you are looking for?
Samsung WF337AA Front Load Washer Logo

664 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Chris Haynie

Level 1 Expert

3 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...