Question about Pioneer VSX-D458 Receiver

Open Question

"POWER OFF" My reciever will not turn on. When i press the power button to resume from stand-by i hear the relay click, but after about 1 sec the units screen reads "Power Off" (blinking for a few secs) and returns to stand-by. I am sure something was over loaded because when i discovered the problem the Volume knob was at max (Someone had sat on the remote) but no actual audio signal was being passed through. I have not done much more than a visual inspection because I was hoping with such an older model more info would be on the web. Anyways. All fuses check and no joy on manuals online.

Posted by on

  • earmstrong13 Jan 24, 2009

    My reciever will not turn on. When i press the power button to resume from stand-by i hear the relay click, but after about 1 sec the units screen reads "Power Off" (blinking for a few secs) and returns to stand-by. How do I fix this?

  • wayne275 Mar 09, 2009

    I have the same problem but my volume was set at 0.

×

4 Suggested Answers

SOURCE: stand by button flashes but receiver wont turn on

Thanks so much for the help on Enter-Adv Surround - fixed my problem as well!!! I love the internet!

Posted on Jan 16, 2008

dunnbiker
  • 8546 Answers

SOURCE: won't power up; push power button on, hear click in back left of unti, get nothing on front display and no output from speakers; as if unit trying to operate

Disconnect the speakers and see what happens. Carefully examine the speaker cables for unwanted connections (shorts).
Take a clue from when the power problem appeared. Something was moved and made the buzz a (probable) dead short.

Posted on May 16, 2009

  • 5 Answers

SOURCE: pioneer elite VSX-92txh freezes up and cannot be turned off

There is a fix for this problem

Posted on Dec 19, 2009

  • 128 Answers

SOURCE: My Pioneer VSX-D1S A/V receiver will not power on

Unit is pretty old I had one of these back in 98-99.

Time to upgrade a service tech is going to cost you $150 just to open it up and figure out whats bad.

Pioneer ok but check out Denon's line of receivers Onkyo is good too but they have a high rate of repairs

Pioneer doesn't make them like they used to that D1S was a tank, had tons of audio / video inputs was one of the first with video upconverting had lots of power and a great front display panel. BUT technology has come along way and pioneer hasn't kept up. They even stopped making high end TV's a few years ago even though they were regarded as the best sets out there.

check this out
Denon AVR-4310CIgoogle it they sell for ALOT less than sticker I bought one for $1299 with a 5 year warranty

Hope that helps


Posted on Feb 19, 2010

Testimonial: "@thebigdoghim, thanks for the very constructive feedback. I was 80% certain that the cost to diagnose the problem alone would be in the triple digits."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon iP2772 doesn't start after saying Ink Absorber is full. How should I fix it?


Dear
First you have to enter into service mode of printer. To Enter Service mode pleas follow below steps.

1. First turn off the printer normally without disconnect power cable.
2. Now press and hold Resume button and press Power button with the resume button.
3. Now keep pressing the power button and release the resume button.
4. Now Press Resume button 5 times and release both buttons..
5. Now your error message will disappear. It mean now your printer is in service mode

Now download cannon "iP2770.exe" reseter from internet and double click on it.
Load some papers in your printer and press the "Main" Button on the reseter window, wait until it shows "error 001" then press OK.
Next press "EEPROM" button and the printer will print some text, after that click on OK button.
5. Then power off the printer(press twice the power button to turn off) and turn on again.

Now your printer will work as normal. How to Reset Canon ip2770 with Service Tool v3400

Thanks.

Jan 31, 2015 | Canon Office Equipment & Supplies

Tip

Resetting the Ink Waste Absorber Error Message


Below Works with most Canon Range of printers.
By using this tool you can reset the waste tank counter and can sometimes reset the ink level monitors.I have included two procedures.

Method 1 1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

Method 2 First you need this tool : http://www.ziddu.com/download/14685220/PCM_servicetool.rar.html
Then the following steps: Step 1: enter in service mode in order to use the resetter:
  • Turn off the printer without pulling the power cords.
  • Hold down Resume button and press Power button.
  • Keep holding down Power button and let Resume button go.
  • Then Press Resume button 5 times then let both buttons go.
  • The Alternate Blinking error is gone: the printer is in Service Mode state.
Step 2:
Extract the resetter and double click "servicetool.exe"
  • Click Reload Button and you will get a new USB port.
  • Load some papers in your printer and press the "Main" Button, wait until it shows "error 001" then press OK.
  • Then press "EEPROM" button and the printer will print some text, after that click OK
  • Then power off the printer (sometimes you have to press twice the power button to turn off) and turn on again.
  • That's done.
I hope this helps anyone who has a issue with the Error codes. You can usually reset it 2 times before it will actually overflow. It can also assist in re-setting error codes

RegardsGM

on Apr 21, 2011 | Office Equipment & Supplies

1 Answer

E 5


1. Start with printer off

2. Press and hold resume Button (triangle in the circle) and click "Power" button. green led should be on

3. hold the Power button, release Resume Button.

4. Without releasing the Power Button, double click "Resume" button and then release Both Buttons.

5. Click "Resume" for four times then click "Power" button, to confirm the selected action (reset counter absorber).

6. Turn off the printer and turn on again


Feb 27, 2011 | Canon PIXMA MP240 All-In-One InkJet...

2 Answers

I have installed Continuous Ink System on my canon ip2770 printer but it still reports my color cartridge has ran out of ink. How can I reset the ink level of the cartridge on my printer?


Press resume button for 5 secs. This works for other canon models using cis.
Thank you for using fixya, have a nice day!
If this helps, please rate me :)

Jan 17, 2011 | Canon iP2700 Inkjet Photo Printer

1 Answer

Hi..i got error 6C10 during printing starting..what does it mean?


Follow these steps :
1.Start with printer off
2.Press and hold resume Button (triangle in the circle) and click "Power" button. Green led should be on
3.While holding the Power button, release the Resume Button.
4.Without releasing the Power Button, click "Resume" button for two times and release Both Buttons.
5.Click "Resume" for four times then soon click "Power" button, to confirm the selected action (reset counter absorber).
6.Turn off the printer and turn on again

Nov 07, 2010 | Canon PIXMA iP4000 InkJet Photo Printer

1 Answer

My printer keeps saying error 6c10 what do I do


Follow these steps :
1.Start with printer off
2.Press and hold resume Button (triangle in the circle) and click "Power" button. Green led should be on
3.While holding the Power button, release the Resume Button.
4.Without releasing the Power Button, click "Resume" button for two times and release Both Buttons.
5.Click "Resume" for four times then soon click "Power" button, to confirm the selected action (reset counter absorber).
6.Turn off the printer and turn on again.

Oct 29, 2010 | Canon PIXMA MP620 All-In-One InkJet...

2 Answers

Error 5b00???


1. Unplug the printer (NO power or any connection)
2. Flip the whole thing Up side down
3. At the bottom, you can see there are screws
4. they are for the generator of the power supply
5. Take them away
6. And slowly take away the "brown" box”
7. Then you will see a power cord links with printer
8. Use a very small driver to release it with real care
9. Leave it for 30 minutes
10. Put it back together .... done

After that
Also, from other, but work....
The reset procedure (for canon MP130) is:-
Turn on the machine
(1) Press MENU
(2) Press SCAN COPY SCAN to enter service mode
(3) USE > to got to NVRAM ACCESS
(4) set ABS-M LEVEL to 0
(5) set ABS-P LEVEL to 0
(6) Press STOP to EXIT
DONE !

Aug 06, 2010 | Canon MX300 Office All-In-One Printer

2 Answers

Instead of printing, the printer ejects empty paper and shows Error code 6000. Restarting the printer as recommended in the manual doesn't help


Hi,

This Error (error 6000) occurred while attempting to print something. Follow this instruction to clear it.

1) Reset your device:-
  • On the operator panel, press and hold the ON/OFF button for one second. (The display will go blank.) If pressing ON/OFF button does not shutoff the device then unplug the power cord.
  • Wait Approx. 10 Sec then press power button ON/OFF button again.
  • Wait until the device has completed its cycling process before submitting another job request.
or
2) Remove Paper Jam if any
Else your device need service (repair)

Good luck...don't forget to rate the solution

Feb 23, 2010 | Canon PIXMA MP830 All-In-One InkJet...

2 Answers

Ink absorber is full on my Canon MP 160...what do I do?


1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Nov 13, 2009 | Canon PIXMA MP160 All-In-One InkJet...

4 Answers

PROBLEM COPYING WITH MY ALL- IN- ONE


This message is inbuilt into most Canon printers, there is spongy thing in the printer which when fills up fires the message (it's mostly a counter in the printer, which can be reset more later...), per Canon this can only be dealt with in a lab but some of the more adventurous have tried cleaning it by themselves. Note that in a lab they won't clean it, it's a part that needs replacing and it might cost around $60. In most Canon printers there is a reset procedure that can reset the error and allow you to print some more before handling it again. Following are the reset procedures for some of the Printers: (not that F60 isn't listed here) Canon GENERIC "S" SERIES RESET CODE Waste Ink Counter Reset. (1) Turn off the printer. (2) Press and hold the RESUME button, then press and hold the POWER button. (3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset" or move momentarily. If the above was properly performed the printer will enter the "Service Mode". (4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press. 1. Service/Factory test printout, including ink sensor check. 2. EEPROM - Info printout. 3. EEPROM - Initialization. 4. Reset the Waste ink counter. 5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!) After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer. ++++++++++++++++++++++++++++++++++++++++++++++++++ Canon PIXMA iP1000 Waste Ink Counter Reset Manual for Service mode 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green. 6. Release both buttons. ++++++++++++++++++++++++++++++++++++++++++++++++++ Canon PIXMA iP1500 Waste Ink Counter Reset. Manual for Service mode 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green 6. Release both buttons ++++++++++ ++++++++++ ++++++++++ ++++++++++ ++++++++++ Canon i320, i255 Waste Ink Counter Reset. Step 1 : Manual Temporary 1. Unplug power and USB. 2. Open door and hold power button. 3. Connect power. 4. Close door, then release power button. or Step 1: Manual Temporary 1. Turn off the printer. And disconnect the printer cable. 2. Press and hold the POWER button, turn on the printer. 3. The indicator (L.E.D.) should be green. 4. Press and release the RESUME button , the indicator (L.E.D.) should be orange. 5. Press and release the RESUME button again, the indicator (L.E.D.) should be green. 6. Release both buttons. step 2 : Software for Permanant 1. Reconnect the printer cable. 2.Open General Tools software and select (USB PORT) 3 .Choose (SET DESTINATION 1) And it should be reset. Remark "After service mode Pls use software for permanent reset" ++++++++++ Canon i850, i950, S600 Start with the printer OFF 1. Hold down RESUME and then hold down POWER 2. release RESUME 3. press RESUME twice, then release POWER 4. Let green light blink until printer is done futzing Select function with RESUME press POWER to execute: presses - light color - function Number of presses - light color - function 0 presses - green - Test print (or exit service mode on i960) 1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960) 2 presses - green - EEPROM initialize 3 presses - orange - Reset waste ink counter ++++++++++ Canon S450 Printer 1: Power off printer 2: Hold Resume button then press and hold POWER, the beeper will sound once. 3: Hold POWER and release RESUME 4: Press RESUME twice 5. Release Power button 6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange. 7: Press Power to set data ++++++++++ Canon BJC 1000 Serie 1: Remove Cartridge 2: Unplug the AC Power Cord 3: Hold down the RESUME button 4: Release RESUME after plugging in the AC Power cord. 5: Press the RESUME once within 5 seconds and release the RESUME . 6: Press and HOLD RESUME for two seconds or more and release it. 7: Press and HOLD RESUME for two seconds or more and release it. 8: Unplug AC Power Cord to set data. ++++++++++ Canon BJC-2000 BJC-2100 Serie 1: Remove the Cartridge 2: Unplug the AC Power Cord 3: Close Front access panel 3: Hold down the RESUME/RESET button and plug in the AC power cord 4: Release RESUME/RESET after plugging in the AC Power cord. 5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET . 6: Press and HOLD RESUME/RESET for two seconds or more and release it. 7: Press and HOLD RESUME/RESET for two seconds or more and release it. 8: Unplug AC Power Cord to set data. ++++++++++ Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265 Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650 Unplug Power Cord Hold POWER and RESUME buttons Plug in Power Cord Release buttons Open front door of printer Hold the CARTRIDGE and RESUME buttons Press POWER Release all buttons after the beeps Press CARTRIDGE once Press RESUME ++++++++++ Canon BJC-5000 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN. 6: Press Power to set data Service Test Print 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN. 6: Press Power to Print Nozzle Print 1: Power off printer 2: Press and POWER, until the printer beeps and release. Demonstration Print 1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps. ++++++++++ Canon BJC-5100 Self Test Switch Printer off. Hold Power for 1 beep. Waste Counter Reset 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN. 6: Press Power to set data Service Test Print 1: Power off printer 2: Press and hold RESUME then press POWER, The indicator will start blinking. 3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode 5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN. 6: Press Power to Print Nozzle Print 1: Power off printer 2: Press and POWER, until the printer beeps and release. Demonstration Print 1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps. ++++++++++ Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620 Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500 1: Power off printer 2: Hold Resume button then press and hold POWER, the beeper will sound once. 3: Hold POWER and release RESUME 4: Press RESUME twice 5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange. 6: Press Power to set data ++++++++++ Canon BJC-600 BJC-600e BJC-610 BJC-620 1: Unplug Power Cord 2: Hold POWER and FF and Print Mode buttons 3: Plug in Power Cord 4: Release after the beeps ++++++++++ Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70 1: Unplug Power Cord 2: Hold POWER and RESUME buttons 3: Plug in Power Cord 4: Release buttons after the printers starts up 5: Hold CARTRIDGE and RESUME 6: Press POWER 7: Release all buttons after the beeps 8: Press CARTRIDGE 16 times 9: Press RESUME 10: Unplug the Power cord ++++++++++ Canon BJ-30 BJC-35v BJC-70 F14 Error Reset 1: Unplug adapter 2: Hold POWER 3: Plug in ADAPTER 4: Release POWER after printer starts 5: Hold FF and MENU and press POWER 6: Release after beeps 7: Press <> Cartridge until 1A is displayed 8: Press ONLINE 9: Press POWER to shutoff printer 10: Unplug printer then re-plug printer ++++++++++ Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520 Turn off the printer. Press and hold the RESUME button, then press and hold the POWER button. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily. You are now in Service mode. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press. 1. service/factory test printout, including ink sensor check 2. EEPROM info printout 3. EEPROM initialization 4. Clear the waste-ink counter 5. Printer model setting. (more selections beyond this- leave this alone) After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta ++++++++++ Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA IP3000 above, 1. Turn off printer 2. Hold down Resume button and press Power button. 3. Keep holding down Power button and let Resume button go. 4. Press Resume button 2 times then let BOTH buttons go. 5. Green lights will flash and then stop blinking. 6. When green lights are solid, press the Resume button 4 times. 7. Press the Power button and the printer should turn off, if not, press the Power button once more. 8. Your printer should respond as normal. +++++++++ Canon S900, S820, S750, S520 Turn off the printer. Press and hold the RESUME button, then press and hold the POWER button. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press. 1. Service/factory test printout, including ink sensor check 2. EEPROM info printout 3. EEPROM initialization 4. Clear the waste-ink counter 5. Printer model setting. (more selections beyond this- leave this alone) After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart. ++++++++++ Canon S9000 Turn off printer Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Press Resume button 2 times then let BOTH buttons go. Green lights will flash and then stop blinking. When green lights are solid, press the Resume button 4 times. Press the Power button and the printer should turn off, if not, press the Power button once more. Your printer should respond as normal. +++++++++ Canon MPC190 Reset Waste Ink 1) Enter SERVICE MODE. By pressing Menu Copy Scan Copy Copy 2) Select TEST MODE. 3) Select [8] PRINTER TEST in TEST MODE. 4) Select 3. [EEPROM CLEAR]. 5) Select 0. [INK COUNT]. 6) Press the [Set] key. 7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Jul 26, 2006 | Canon MultiPASS F60 All-In-One InkJet...

Not finding what you are looking for?
Pioneer VSX-D458 Receiver Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4706 Answers

John
John

Level 2 Expert

473 Answers

Dennis McCollum

Level 2 Expert

137 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...