Question about Foxconn 865G7MF-SH Motherboard

1 Answer

Wiring of motherboard

My wiring was pulled off my board and i put it all back but i dont know if it is all in the right order because when i go on the internet for so long my screen goes blue and i get some writing telling me that windows is shuting down in order to protect my computer and i do not know much about computers at all

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 397 Answers

The blue screen you are seeing is known as the BSOD (blue screen of death).
Usually the BSOD is associated with a hardware fault, if you are saying that you have just been moving your motherboard cables about, you had better go back and check the security of the harddrive data cable (the grey flat one) and the security of the memory sticks in their slots.
If they are sound then you will need to download harddrive diagnostic tools from the harddrive manufacturers site and memtest86 to test the memory with.
Memory is better tested by substitution as memtest can take hours to run.

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the order for placing wires black in place. for front panel and reset, L ED. placement order for which they are placed back on the switch.


The wire placement is usually written small right on the motherboard. Each front panel connector should be labeled.
Here is the owner's manual for the motherboard:
http://download.intel.com/support/motherboards/desktop/d815eea/EA_ENGLISH.PDF
(Hint: Copy the whole link to notepad, make it all one long sentence, copy again and past into your browser)

Mar 22, 2010 | Zerus Intel Desktop Board D815EEA...

1 Answer

Dont have a manual, cant find one , dont know where to hook the start button wires....


Hi,

You will need to look for the full product code (model) of your motherboard in order to get the right manual online.

You can visit this link:
http://support.asus.com/images/rev_no1.gif

in order to see the relative location of your motherboard model.

From the same site, you can find your manual.

Hope this helps.

Jun 27, 2009 | ASUS SiS Chipset P4S333-M...

1 Answer

Usb


please click follow:
http://www.pctechguide.com/tutorials/MBoard_USB.htm
acording the table and picture you can make easy to correct your USB connection.
hope help you fix it, any question send any time please!
please take a rating let me know how much helped you, thanks!

May 17, 2009 | MSI 865PE Neo2-PFS Motherboard

1 Answer

How to place indicator led cables to motherboard


hey look close to the nearby processorin motherboard there is 9 pin (depends on motherboard) for power and for reset button... close your eyes to motherboard at that place you will find also the name which are mention in motherboard e.g. power and reset in motherboard just plug red wire in power and and green for reset ( depends on motherboard) you an chk manually ...

Apr 05, 2009 | Motherboards

1 Answer

I had a keyboard failure on start up


The error message indicates you posted (power button green, video on the screen... keyboard failure error message). But your comments indicate the power button is yellow/orange. That indicates a "no post".

If the power button is yellow, disconnect everything from the motherboard, but the connections for the power supply and control panel (power button). Turn it back on.

If you get a green power button, and the system beeping at you add the memory back in. All four slots MUST be filled!!! If it's still green, add the video card back in. If that works, keep adding things one at a time until it either works, or you know what's causing the problem.

If you get a yellow button, check your heatsink. You just replaced the motherboard. You might not have gotten it right the first time. If everything is tight, and all the power connections are tight and plugged in (if I remember right, there should be a 20 pin and a 4 pin connector), it might actually be a bad board. Try swapping the old board back in and see if you get a different response (if so, the new board is bad).

Dec 19, 2008 | Dell (F2273) Motherboard

2 Answers

Mother boards


For K8M-800M:
  • See the following diagram and try to make connection
183ab55.gif For complete manaul click.

Thanks
Iqbal

May 26, 2008 | Intel Motherboard

2 Answers

I have an p4p88-e mother board in my tower


...if its onboard(Meaning built into the botherboard) how did you take it out??
Puting in any Video card that fits will at least get you to bios. If you want to start windows though, you will need to re install windows, as it will think it was copied from one computer to another(It looks at the motherboard.)

Feb 21, 2008 | ASUS P4P800E Deluxe (90M8LCW0G0EAY)...

1 Answer

Instaling soltek sl-kt400-c


Oops you could have blown the board. do you have the origional mother board book that came with the board first day. If so check your wiring.

Dec 09, 2007 | Motherboards

1 Answer

Power Switch


This board I think is an OEM board built by Asus for HP computers. Also named Pegasus.
Go here to find a PDF manual for that particular board -
http://www.ctechinfo.org/manuals/pegasus_manual.pdf
On page 22, the last page, it shows you the pin-out for the connections for the front panel, ie - power button, reset, led's, etc. Hope this helps.

Oct 23, 2007 | ASUS CUV-NT (CUVNTWOTVWOV) Motherboard

1 Answer

MY MONTOR HAS POWER AND IS NOT WORKING.


Hi, dont loose faith. If you look on your mother board along the edge closest to the front of the case you will see a series of pins, usualy about 10 pins. Printed on the board will be the names of the plugs that match. The wires from the front of the case have corresponding names. The power and reset switch will work no matter witch way around you put them. The HDD led and the pwr led will only work one way so if these lights dont work, just reverce the plugs. If desperate you can bridge two pins together at a time until you get the on/off switch. Note you cant hurt anything unless you use a hammer. Regards mistyman

Sep 03, 2007 | FIC FR33E Motherboard

Not finding what you are looking for?
Foxconn 865G7MF-SH Motherboard Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Foxconn Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers

Are you a Foxconn Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...