Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

1 Answer

Fitting "Bushes hi there, Please could you tell me how replace the bushes on my Hotpoint Aquarius 1300, washing Machine. Regards Mike..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers

You will have to remove the back then the motor then the motor brushes

Posted on Sep 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing bushes hotpoint wdf740


check the length of the motor brushes.
new are about 30mm long.
should also clean up the motor with compressed air.
Remove the electronic module also do a cleanup in all contacts of connectors. If necessary wash with isopropyl alcohol which can be purchased at a pharmacy.
Dry with a hair dryer.
Do not forget to make reset to clear the error.

(Pressing the start button until all the LEDs light up)

Dec 21, 2013 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Hotpoint pump


Is the machine not spinning? May need new bushes. Sited underneath and wear down by making contact on drum.

Feb 05, 2012 | Hotpoint Aquarius WF210 Front Load Washer

1 Answer

Hoover Aquarius Washer Drier WD 440 Washing machine worked fine yesterday but today is tripping out and blowing everything in the house. Also washing inside the machine was very hot and water not drained...


sounds like the bushes have gone in the motor... about £20 from your local appliance retailer/parts department! or the filter may be blocked... clear the filter but it will get messy so have towels at the ready a hosepipe would come in handy or move it outside if you feeling strong!!

to check the bushes locate the motor not sure of position on these but near to the bottom you will see wires going to plastic parts each side normaly held in by a screew, take a wire off each plug in and see if it runs...

hope this helps

Aug 30, 2011 | Hotpoint Aquarius WD63 Front Load...

1 Answer

How do i change bushes on my wf440


hello go to this site www.espares.co.uk it will show you how to replace them or youtube hope it helps

regards
shaun

Apr 05, 2011 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

My washing machine it tripping the mains board out, changes plugs and sockets and its still doing it - any ideas? perhaps the bushes?


sounds like water is getting into the electrics....or your trip circuit has became week...try switching the trip switch from another circuit.

Jul 21, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Hotpoint Aquarius 900 WM61, washed but stopped spinning, about 6 wks ago, new brushes fitted old 1's had split everything worked fine, 6 wks down the line machine washes but doesn't spin again, bushes are...


hello carl check the module circuit board this controls the speed check the transistor on the boards for dry joints if discoloured change the board all the best

shaun

Aug 04, 2009 | Washing Machines

1 Answer

Changing bushes on a hotpoint wd63


There is a screwdriver that you may need to buy that has a retainer on it to hold the screw in place while you attempt to seat it in the hole. Here in the States we call the place to buy one of these the Hardware Store. There must be a store where you can explain the tool you need based upon my description.

After you replace the bushes for the machine you will want to replace the bushes for the motor as well. So, the motor will have to come off now or sooner than you realize. When one goes the other is soon to follow. So, while you have everything apart and are in the midst of it all you may as well do the motor while your at it.

I also assume you were able to manually move the machine and it is not seized by frozen bushings or bearings.

Hope this helped and fixed ya.
Worldvet

May 21, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint aquarius 1300


it takes a fitting stap to fit but can be put back on by hand little tricky but can be done no probs

Mar 01, 2008 | Hotpoint Aquarius WD640 Front Load...

2 Answers

Hotpoint WD61


1, your pump may be blocked by fluff coins and other debris.
2. more likely bushes worn on the main motor not giving enough umphhh (loverly word) to go through a complete spin....Bushes easily replacable. Job start to finish with parts on hand a machine mechanic 10-15mins top Diy er like me an hour allways have trouble finding the right spanner... Good luck.

Jan 06, 2008 | Hotpoint WD62 Front Load Washer / Dryer

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...