Question about Arris DSR922

2 Answers

I cannot get in any digital signals today.

I have a motorolla 922. Yesterday, all is fine. Today, I cant get any digital signals or two green lights. I have tried all I can think of. Thanks, Mike

Posted by on

  • 2 more comments 
  • Anonymous Sep 01, 2008

    analog channels are fine can't get green ( DC) light tried eveything

  • nyln Dec 13, 2008

    the digital side is not working need some information on how to resolve this issue

  • Anonymous Dec 27, 2008

    Yesterday the machine went out completely. The supplier is on vacation until after New Years so cannot get help there. I have no idea on what to do.

  • johnm95127 Feb 08, 2009

    All my digital channels work good except om W1. I subscribe to the Denver 8 and about a month ago I lost them then a few days later they were back and now they are gone again. All I get is cannot find channel continuing to search. No green light.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same thing happened to me. After much research I found out that the digital descrambler was dead. I found a good used unit on e-bay, but I found out later that the repair usually averages about $120. I plan on getting the old one repaired for a spare. Contact ATS Electronics at 828-465-9968. They have a set labor rate of $98 plus parts.

Posted on Dec 26, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

When the backup battery goes dead you loose the ID number.
http://www.pacificsites.com/~alanjudd/922.htm
If you have lost your receiver ID number you will need a new main board.
Check the receiver number in the status screen. If it matches the UA number on the back sticker you are ok, if not the only solution is replacing the main board. ATSelectronics.com still had some boards when I last checked. But when they run out were all screwed.
Motorola didn't make any provisions for renewing the ID number.
That really sucks motorola ;-(

Posted on Jan 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New customer. Installed yesterday. Worked fine last night. Turned on today, all I get is searching for signal on satellite in 2.... (771).


Go to your menu and find your signal strength bar.It's possible that your dish has shifted.The bar should read at least 60% or above.

Sep 25, 2010 | Directv Plus DVR DTV Receiver / 100-Hours...

1 Answer

Lost Digital TV signal - now back but weak - any suggestions?


I would get someone to check the signal strength first.

Dec 07, 2009 | Televison & Video

1 Answer

Humax Foxsat HDR sudden Remote Control failure..


Make sure you have pressed the "PVR" button at the top. If you have accidentally pressed on on the others TV, DVD or AUDIO then they will light up when you press another button signifying that the remote is trying to send a signal to them rather than the PVR...which is where you want it to go.

Nov 10, 2009 | Televison & Video

1 Answer

Cant reset my thomson 250gb dvb top up tv box


go to menu, then set up(4), then help(6)
then press green button (yes i know it doesn't display that option)
you then have three options
suggest format hdd as a start
i have had to do this at least twice
also my 6300-16 was playing up badly today, after unplugging it took about 15 mins before all the flkashing lights calmed down+

May 03, 2009 | Televison & Video

1 Answer

Top up tv+ digital tv stopped working.


i had same prob, tried unplugging three times
then unpluuged for 5mins
, plugged back in left it alone, ie didnt touch remote or front panel, until it settled down ~15mins, green light came on (doesn't normally)
and everthing seems ok now

May 03, 2009 | Televison & Video

1 Answer

I get get digital signals on dsr 922


does the creen say searching for channel? if so you might have to update the maps...go to G! 3 and leave there for about 15 to 20 minutes...make sure you got a dc light....if no you have a tuning issue...play with the skew...

Feb 16, 2009 | Arris DSR922

1 Answer

No Signal


I give up trying to get this to work. This thing is a joke. We will just go purchase an American made Digital tv today. The "800" that came with the DTV converter was answered by someone who didn't give a **** about helping anyone. What a waste of time and money.

Jan 17, 2009 | Televison & Video

1 Answer

Dsr 922 no dc light on g1 etcs


you are not on the satellite. need to reporogram or fine tune these satellite into receiver.

Oct 11, 2008 | Arris DSR922

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Arris Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69878 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6445 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Are you an Arris Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...