- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Certain parameters are hard-coded into the chip but you can clear temporary data by restoring factory defaults or erasing the channel memory. Here is a link to the manual: Toshiba 32C120U User Guide Page 2
Check the Chanel 7 broadcast signal on the other tv have sound,could caused by the tv broadcasting signal from the tv station itself.Check if ur tv have a function known as S.A.P. make sure it is off,could effected no tv audio problems,because the tv station in ur city or town don't broadcast in that signal frequencies.
U can't in most cases,that why they called a secret passwords codes.U only can tries this by unplug the converter box and replug it back 24 hours later.Go to parental control codes mode and resetting the mode,might resetting the mode and erase the secret passwords codes,only some models of boxes could do this,ur included don't know sorry.
An attenuator reduces all signals. Attenuators are often used when you are close to a transmitter that causes interference to other stations. By knocking the signals down, the strong signal is less likely to interfere with the other stations, while the other station's signals will be reduced too - many can now be tuned and viewed. This comes with the risk that some stations that had a signal that was just over the threshold of being tuned and watched no longer have a signal level that passes through the attenuator. This is what is happening in your situation.
Determine if you can watch stations you like without the attenuator. If so, do not reinstall it. If you find that some of the stations are being interfered with by another station - see if you can change the amount of attenuation in the device. Some attenuators are adjustable and make this easy to do. If yours is not adjustable, you might consider purchasing an adjustable type - as the one you have is not suitable.
Lastly, consider installing a rotatable antenna. This will allow you to aim the antenna directly at the broadcaster's antenna - allowing you to reject signals not in the same direction. This should reduce your interference from other strong signals that originate from a different direction. This will also increase the signal strength from all transmitters as you can point your antenna directly as the antenna - instead of capturing signals from the side or back of your antenna.
I hope this helps and good luck! please rate my reply. thank you.
Due to security reasons, passwords can only be changed in the web admin interface. If you forget the admin password, the NAS would have to be reset by a service technician. If you have access to the web admin interface... All passwords can be changed in the User list (Share -> User). Click the User ID to change the password.
Off-Air reception (Antenna) of TV Guide comes from a supplier called Rovi (formally known as Macrovision, Gemstar). They have supplied your local CBS affiliate with a TV Guide application known as SCTE 127 or VBI in MPEG. Follow these steps until you have found a solution to the TV Guide - No Information Available.
1. Check to see if your local CBS station is coming in clearly not tiling.
2. Reset your TV Guide through your TV Guide Menu, for more information copy and paste the link below. (What usually works for me is setting up the guide by putting in 99999 for the zip code then answer all other questions. After it says your TV will receive the guide in 24 hours then setup the guide as you normally would with your zip code).
You might have a Service Co. come out and look at it. It sounds like the Z module is not doing it's job of erasing all prior images after a scene change. Some models there are adjustments for that internally. ( only for a tech ) Start a paper trail now.
you need to make sure your plugged into the cable input on the back, not the air input, if it is, go into the menue, find setup, then chanel maniagment, or auto program, or somethiln similar, then do the auto program, it will fix your problem, hope that helps, and thanks for your rating