I've same issue as yours..

Hi, Anonymous before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
YZF600R Forums View topic Led turn signals won blink
Yamaha R15 Warning light error codes Team BHP
Yamaha YZF R15 Service Manual
OEM parts for Yamaha
Yamaha YZF R15A Owner Manual

Google your dishwasher you will see parts on line There are loads just looked .

Assuming the unit is plugged in, this could be an issue with the power supply, or an issue where the cord connects to the laptop. If the power connector on the back of the laptop is secure / doesn't feel loose or damaged, you may want to simply get a replacement power supply from a local electronics store. Be sure to take the make and model information of the laptop and the power supply with you to the store.

If you want to keep your important data, use some softwares can solve thewindows won't startproblem most quickly, and no data will lose. Besides, it is very easy, even the people who lack of computer knowledge can deal with windows won't boot issue.

Hi there,
It sounds like a hardware issue, if you're getting the LED's blinking when pressing power, there IS power to your mainboard (which is a good thing). Some manufacturers have placed LED blink codes within the system to let you know what's going on, but I have a feeling it's either A) your battery or B) your hardware, such as a bad RAM stick.
Try removing the battery and with the power plug connected switch the laptop on. If it works, you've got a bad battery.
Try removing a single RAM stick or replacing both.
You could search HP Pavilion LED blink codes to further address the issue.

Power supply probably fried. You will have to take the TV apart to test.

Unfortunately it sounds like you have an issue with your motherboard. If you remove the battery and just try to power on the laptop using the AC adapter and it still won't power on then it's probably the motherboard. The power supply circuit (where the AC adapter plugs into) for the motherboard is integrated into the motherboard.
Sorry. If it's still under warranty Dell will replace the motherboard.

It may be a loose solder on the circuit board where the spade connector is set into the printed board. Not easy to see but there may be a hairline crack. I've repaired this issue with a small soldering iron. From the factory wires are secured by zip ties or some sort of fastener, and pulled tight. This sometimes does harm to the board. That red light may have some small letters next to it on the board indicating a fault, and you moving the wire was actually a loose connection that reset it. And the loose connection had nothing to do with the main issue at hand. The red blinking light may be a trouble code also. Count the blinks, or if continuous, may give a fault code. Most pool heaters I've worked on have issues with high limit, meaning the unit faults due to overheating. And many times I've had the maintenance guys back flush at the pool filter/pump system, cycle off the heater(furnace) at the main power disconnect or breaker, and power it back up. Simply turning off the switch on the unit may not reset it. Be safe and ensure all wires are place back to their original position and that all voltage is turned off when servicing. And that all run capacitors are properly discharged before servicing. Hope this helps!

Hi, Imcook2 before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-fireblade/51008-cbr954rr-led-turn-signal-flasher-relay.html
turn signal issue CBR Forum Enthusiast forums for Honda CBR Owners
Honda 954 Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR954RR Owner Manual

Hi,
First, we need info about your laptop brand, model, and OS
Please remove the battery, hold on power button for about 50-60 seconds, then plug-in the charger and turn the laptop ON,
Please tell us your results
Good Luck