When I start this laptop all I get is please choose an option start microsoft windows repair reinstall windows advanced options exit and restart computer

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery

To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions

This could mean that the copy of Windows installed in your computer is either corrupted or damage and reinstalling or repairing your Windows should fix the problem.
But try doing System Restore first on safe mode before doing a Windows reinstallation or repair to save you from loosing all you files in your computer.

To do system restore on safe mode:

1. Restart your computer and when the Dell Logo comes up and keep pressing F8 until an option shows
2. Use arrows to navigate then choose safe mode
3. Click start button then choose All programs or Program depending on the Windows installed in your computer
4. Click on System tools then choose System Restore
5. Follow the intructions on the System Restore windows on how to restore your machine back to a previous date before this issue happen.
6. Your computer will automatically restart after restore is done

If the safe mode doesnt work then your last option is to reinstall or repair your windows:

1. Press F1 to go to BIOS then change boot priority - make sure your DVD drive is the first boot
2. When your done changing boot sequence press F10 to save and exit
3. Insert you Windows CD and and a meesage will appear on a black scrren "Press and key to continue" press any key. Windows file will load and options for Repair or Installation will appear
4. Choose 1 of the option then follow the instruction (Installing a fresh copy of windows is recommended)

Hope this information will be helpful. Thank you for using FIXYA.

This error message means that the copy of Windows installed in your computer is either corrupted or damage and reinstalling or repairing your Windows should fix the problem.

But try doing System Restore first on safe mode before doing a Windows reinstallation or repair to save you from loosing all you files in your computer.

To do system restore on safe mode:
1. Restart your computer and when the Dell Logo comes up and keep pressing F8 until an option shows
2. Use arrows to navigate then choose safe mode
3. Click start button then choose All programs or Program depending on the Windows installed in your computer
4. Click on System tools then choose System Restore
5. Follow the intructions on the System Restore windows on how to restore your machine back to a previous date before this issue happen.
6. Your computer will automatically restart after restore is done

If the safe mode doesnt work then your last option is to reinstall or repair your windows

1. Press F1 to go to BIOS then change boot priority - make sure your DVD drive is the first boot
2. When your done changing boot sequence press F10 to save and exit
3. Insert you Windows CD and and a meesage will appear on a black scrren "Press and key to continue" press any key. Windows file will load and options for Repair or Installation will appear
4. Choose 1 of the option then follow instruction


Hope this information will be helpful. Thank you for using FIXYA.

Hi, To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions

Hi,
You may not be able to access the recovery partition because you have reinstalled the OS.
Make sure that AC power is plugged in to prevent shutdown.

To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions

Good luck.

Should your Windows develop serious errors or fail to start, you can restore your computer back to factory settings by using the hard drive recovery located on a hidden partition on the hard drive.
To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions

If this has helped you out then please rate me!

To restore your computer back to factory settings, follow the steps below:

1. Turn on the computer and keep tapping F8 until the advanced options menu is displayed
2. Use the up/down arrow keys on the keyboard to highlight Repair Your Computer and press enter to select it
3. Select the language you wish to install (normally English is the only option)
4. Once you have chosen your language you will be presented with the available recovery options
   • Microsoft Repair Environment - after choosing the UK keyboard layout you will be asked to choose the Operating System you wish to repair. If Windows Vista is not listed then you cannot repair the OS without doing the full recovery. After choosing Vista the Microsoft Vista startup repair tool will run and attempt to repair any startup problems you are experiencing
   • Reinstall Windows - gives you the options available to reinstall Vista
   • Advanced Options - this launches the diagnostic centre allowing you to run chkdsk, launch notepad or bring up a command prompt
   • Exit & restart computer - Exits withut running the recovery process
5. To continue with the recovery program you need to choose Reinstall Windows
6. On the next screen you have the ability to launch Vista System Restore and roll back to a date when Vista was last working ok or to run the Full Destructive Recovery. To continue with the recovery program you need to choose Start Full Destructive Recovery
7. After choosing the Full Destructive Recovery option you are presented with the warning screen that all data will be lost. It is important to make sure all data has been backed up to disk if possible and to realise this process deletes all data and reverts the machine back to it's default state. To continue with the recovery program you need to tick the box indicating you are aware of data loss
8. The recovery process will then run through, the computer will restart a couple of times during this. You will also need to go through the Vista "Out of Box Experience", to configure Vista. This is fairly straightforward so just follow the onscreen instructions

So to install HDD recovery, please do as follow:

• Start your notebook after the bios screen press F8 to enter “Advanced boot options” (if you get the timing wrong, just restart and keep pressing F8)
• Choose the first offered option “Repair my Computer” to enter Vista “System Recovery Options”
• Choose the last option – Toshiba recovery option
• Follow the menu on the screen

Please note that whole HDD will be deleted and if you have some important data please back it up