Question about Projection Televisions

1 Answer

Picture slow to appear - Projection Televisions

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 50 Answers

Does if blurry from the start?

Posted on Aug 11, 2008

  • milmar
    milmar Aug 11, 2008

    if it does replaced the CRT socket. and if not the picture tube maybe weak if it is an old TV.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I adjust the contrast w/o contrast control?


Almost all sets have a brightness and contrast (which is often labeled picture instead) in the main customer menu-----look to see if it changes the picture or not.

If issue is the picture is there but somewhat slow to appear or dim the model indicated uses a lamp which may be the real problem...

Oct 30, 2012 | JVC HD-56G786 56" Rear Projection HDTV

1 Answer

It takes a very long time for the image to appear


based on model number someone would have to take a look at the three picture tubes this set uses---each with set on has a dim 6.3 volt filament that should be lit when set on---if not you have a loss of that voltage between source and the tubes.

Oct 16, 2012 | Toshiba 51H84 51" Rear Projection...

1 Answer

My 52" rear projectionT.V. Is about ten years old and for the past year the picture takes a while to appear. Sometimes the picture will blink on and off for hours, while other times the picture will only...


You generally have a weak capacitor in the power supply, that will delay a startup! Second to these are poor grounds on any and all ICs attached to heat sinks. A heat sink is a large metal piece mounted on the TV board. It is a cooling fin to reduce heat on the IC. The pins are underneath these, and will have cracked rings around them. These of course reduce voltage and a promote a slow startup. Please check all capacitors with a capacitor checker and look closely underneath the TV board for bad solder grounds and resolder!

Sep 25, 2010 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Too much yellow does not adjust with normal drop screen adjustments. can i adjust the light beams.on my philips 50"


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} 1. Turn the green screen control on the Focus Block until retrace lines appear and gradually turn it back
Until the point where you can see the retrace line disappears, just before cutoff.
2. Turn the red screen control on the Focus Block until retrace lines appear and gradually turn it back
Until the point where you can see the retrace line disappears, just before cutoff.
3. Turn the blue screen control on the Focus Block until retrace lines appear and gradually turn it back
until the point where you can see the retrace line disappears, just before cutoff.
4. If the screen still appears too bright after proper G-2 adjustment, you need to adjust the sub-bright adjustment in the service menu
control down until screen cut-off. (Service data Range is usually 21 to 25 in the Service menu, for Sony sets you first go to category "MCP2", & then adjustment item 01( "SBRT")= subright.
For electrical the focus, put on the screen a clear picture of your choice thru an input of the TV set from a DVD, then pause the playback of the DVD Look into each color and rock that color focus control back and forth (turn the control one way then the other way slowing down as the picture goes into the best focus. till the picture looks sharp do each color till they all look in focus. NOTE: it is best to look into each color tube to achieve the best electrical focus. For optical focus please follow the manual lens adjustment in the sets service manual
By Larry Dillon

Aug 27, 2009 | Philips 50P8341 50" Rear Projection...

1 Answer

Slow to No picture


What is the make and model number of your tv. Iclude cassis number if it is a RCA, Phillips/ magnavox. Need that info in order to even begin to offer any suggestions as to what may be happening with your set.

Feb 11, 2008 | Projection Televisions

1 Answer

No Picture, Menu screens or anything video - Sound still working!


Yes... Look for F851 and replace it with a slow blow 3.15A fuse per Toshiba. Bill

Jul 01, 2007 | Toshiba 43AX60 43" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...