My bizhub 7228 has this on the screen F-26-1 and says i need to contact service

Hi!

To clear an abort code on a Konica Minolta Bizhub 250 and resume printing, you can try the following steps:

1. Press the "Utility/Counter" button on the control panel of the Bizhub 250.
2. On the touch screen that appears, select "Trouble Reset."
3. Confirm that you want to clear the abort code by selecting "Yes."
4. Wait for the Bizhub 250 to reboot, which should take a few seconds.
5. Try to print a test page to verify that the abort code has been cleared and that the printer is functioning correctly.

If these steps do not clear the abort code and you are still unable to print, you may need to contact Konica Minolta customer support or a qualified service technician for further assistance.

Regards

Service manuals electronic components datasheets and equipment schematics...

try this site for service manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

contact yahoo
Customer Service Phone Number
1-866-562-7219 or 1-866-562-7228

contact yahoo
Customer Service Phone Number
1-866-562-7219 or 1-866-562-7228

call yahooCustomer Service Phone Number
1-866-562-7219 or 1-866-562-7228

try yahoo and see if they can help you
Customer Service Phone Number
1-866-562-7219 or 1-866-562-7228

The parts list is here:
https://www.dixiesales.com/ipl/604/FHH18A.pdf

Here is the gun and wand:
http://www.ordertree.com/partfinder/results/?pn=7228-H18A01 ($47.31)

http://www.ordertree.com/mcc-7228-h18a01/

Part number is 7228-HA18A01

Here is another source for the same wand but there is something wrong with the shipping cost:

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270574885788&clk_rvr_id=238587150997#shipping
To purchase
https://signin.ebay.com/ws/eBayISAPI.dll?SignIn&ru=http%3A%2F%2Foffer.ebay.com%3A80%2Fws%2FeBayISAPI.dll%3FBinConfirm%26item%3D270574885788%26rev%3D0%26fromPage%3D4340%26BinConfirm%3D%26quantity%3D1%26fb%3D1%26BidBinInfo%3D%253CbidInfo%253E%253CID%253E270574885788%253C%252FID%253E%253CMB%253E%253C%252FMB%253E%253CQTY%253E1%253C%252FQTY%253E%253C%252FbidInfo%253E&pageType=2143&onepagereg=1&item=270574885788&ICurl=&ICtitle=7228-H18A01&ICdateMedium=Jun-29-11&ICtimeLong=19%3A58%3A11+PDT

To contact the Seller; you may email [email protected] OR contact Customer Care by phone at 1-877-500-7499.

Thanks for choosing FixYa,
Kelly

These are heat sensor abnormality error codes in Konica Minolta 7222/7145/7135/7235/7228 models.You did not mention the model.

Fusing error
1. Press the Warm Restart switch, and “●” appears at the center on the left end of the screen.
2. Enter “3” from the 10-Key Pad.
3. Type the 8-digit service code and touch [Enter]. (Default value: 00000000)
NOTE
• When [END] is touched after a wrong service code has been entered, the Basic screen reappears.
• At the fourth access after entries of three wrong access codes, [END] is not available on the screen. It is therefore necessary to turn OFF and ON the Main Power Switch.
• If you forget the service code, it becomes necessary to replace the RAMS Board with a new one. Take necessary steps not to forget the service code.
• The RAMS Board is not available as a replacement part. If it requires replacement, contact Office Printing Support Division by way of CSES.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Have the document feeder rollers been replaced? Also how about the Clutches for above rollers been replaced?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f