Question about GE 30 in. Profile JP989 Electric Cooktop

1 Answer

Jp 989 switch replacement

I have to replace the selector switch for the bridge element on my jp 989. I have the switch. I have disassembled from the bottom. It looks like it fastens from the top. Do I have to remve the glass to replace the switch???? How do I accomplish this?????

Posted by on


1 Answer

Not timely but no.
i have a dead switch, had to unhook it cause it kept tripping the breaker. 3 out of 4 work now.
can i buy 1 switch or do i need a whole new assembly. where to buy online ?

Posted on Oct 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No power to right rear burner or bridge, new control board and element installed already. When puower to rr burner is on an H appear on display window, like its hot yet never heated. When you know of...


The issue seems to be with the switch that is bad and should be replaced. Hope this helps...please post back with its model no for further assistance.


Jul 07, 2011 | Thermador Cooktops

1 Answer

One burner (left front) heats up too much. You cannot regulate the temp. Everything heated on this one element burns.

This is usually caused by the infinte switch. You will need to disassemble to acess the switch. The switch is easy to test and replace. Here is a link showing how to test an infinte switch
You can also enter in your model # for diagrams and illustrations of your specific model.

Aug 25, 2010 | Maytag MEC5430BDS Electric Cooktop

1 Answer

I get a hot surface light when the burner is off and has not been used. My wife said she got a fail code but was unsure of the problem and did not write down the code. I have cycled the breaker on and off...

This is usually caused by one of the infinite switches. They are easy to check and replace. You will need to remove the cook top and disassemble to access the switch assemblys. Here is a link that will walk you thru testing the switches You can also enter your model # for diagrams and illustrations of your model.

Jul 16, 2010 | GE 30 in. Profile JP939 Electric Cooktop

1 Answer

I would like a circuit diagram for a Kleenmaid CH 14 Cooktop

Hi, I too have had a problem with the dual element on the Kleenmaid CH14. Likewise I was given an Invensys M82314 which as you will know is not configured in the same way. However, I assume that what they call"phase" is the active connection, the neutral is marked and are side by side like the old one, pilot is idicated and is the wire that bridges together with the other are only left with two...."load1" and "load2" whichever way around I apply those I can only get my inside burner to run. I am baffled !! My old switch operates both burners but keeps cutting in and out.

Nov 11, 2009 | Cooktops

1 Answer

Broken selector switch

TURN OFF CIRCUIT BREAKER. Lift out cooktop, remove all machine screws holding the glass frame. Remove plastic knobs and lift glass top straight up. Make sure rubber gromits are not ripped or torn. Unscrew the small screws on the selector switch and then lift up and tilt over the small aluminum chasis holding the switches to expose the wiring connections. Pull off the wires and pull out the defective switch. Replacre switch, connect wires, re-seat switch chasis, and secure switch with screws. Carefully drop in the glasstop lining up the switch shafts and the rubber grommets. Secure the top with machine screws and drop back in the cutout.

Apr 18, 2009 | GE 30 in. Profile JP350 Electric Cooktop

1 Answer

Dual Surface Selector Switch

more common is the dual switch to be bad, but it is possible that the elemnt itself has burnt out, usually a 5 yr warr on the elemnts under glass

Nov 08, 2008 | GE Profile JP930 Electric Cooktop

2 Answers

JennAir Elec Cooktop Problem

The selector knob having lose contact the elements are for full adjument , the wire connection are rust and corroded need to clean terminal of elements.

Jan 04, 2008 | Jenn-Air 35 in. JEC9536ADS Electric...

Not finding what you are looking for?
GE 30 in. Profile JP989 Electric Cooktop Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Cooktops Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers


Level 3 Expert

77939 Answers

Dave Harrison

Level 2 Expert

114 Answers

Are you a GE Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides