Question about HP LaserJet P2015dn Printer

1 Answer

Printer problem ready & go led is continuslly blinking problem

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 87 Answers

Please provide more information.

Does this happen while starting or printing.
What happens if you press the Go button.
Are you using a genuine HP Cartridge or refilled one.
Try reseating the toner and trays and also check for paper jams across the printer

- Nikhil

Posted on Nov 07, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why all led blinking in speed 40 passbook printer after powering on the printer

Why only 3 lights are blinks in speed 40 plus? ( st1, ready, st2)

Apr 30, 2014 | Office Equipment & Supplies

1 Answer

In tvs speed 40 printer all led light are blinking

follow these steps
1) Press ST1+READY button together
2)Turn on the tvs speed 40plus passbook printer
3) The 4 LED will blink 4 times. Release the button ST1+READY immediately after 4 blinks
4)PRESS ST1 - ST1+READY+EJECT starts blinking
5)again PRESS ST1 - ST1+EJECT+ST2 starts blinking
6)again PRESS ST1 - ST1+EJECT starts blinking
7)again PRESS ST1 - ST1+EJECT starts blinking
8)again PRESS ST1 - READY+EJECT starts blinking
9) printer is READY wait and PUT PAPER.
10) The paper goes in and comes out 3 times. will take about 2 minutes.
11) Paper ejects automatically after printing.
12) turn off the printer and turn it on.

Jan 24, 2014 | Office Equipment & Supplies

2 Answers

Epson R230 with green led and red led blinking

This is general error of the printer. When you have to change the new mother board you should be initialized it then it can be ready mode. When you try to initialization you need printer printer adjustment program. You can batter find out from google & write down EPSON Stylus R230 Printer Adjustment program or ink reseat program.

Jun 12, 2013 | Epson STYLUS R230 InkJet Photo Printer

1 Answer

When printer is turn on that time printer reddy and cartridge light on so what is the problem

You can see four LED's on control panel, from top to bottom,1st is toner indication 2nd Attention 3rd is Ready light, 4th go light.. Observe led's are 'blinking' or 'On' condition.. # If toner light is blinking ="toner cartridge missing or contact problem or memory faulty.
# If toner light & ready lights are on= "toner low indication or refilled cartridge loaded".

Jul 12, 2012 | HP LaserJet P2015dn Printer

1 Answer

My HP Deskjet 1120Cxi fails to print normal document and test printing. My computer operating system is window XP

Power on the machine, check front panel 'cartridge led' blinking? replace the cartridges,if 'paper led blinking' indicates paper jam check for paper jam.If printer comes in ready mode check in system drivers its is ready mode?.. if no check parallel cable if its good replace formatter..

Sep 06, 2011 | HP Deskjet 1120c InkJet Printer

2 Answers

Olivetti pr2 plus station 1 and ready are blinking yellow


Apr 20, 2011 | Office Equipment & Supplies

1 Answer

Solid orange light and blinking green lights

To check the light Pattern of your printer

Click on Light and Error HP Laser jet 1012 Printer

Check the error details from the above link

Condition of the printer Action/Description Ready

The printer is ready to print. No action is necessary. Processing

The printer is receiving or processing data. Wait for the job to print. Processing...(job name) Ready LED is blinking.

This message is displayed while the printer is processing a current job, but has not begun to pick pages. Processing...(job name) From Tray XX Ready LED is blinking.

This message comes up for any job, once the printer starts to pick paper. Manual Feed or Continuable Error

The printer is attempting to Manual feed, media is not loaded in the paper tray, media loaded is the wrong size or type. Verify that the correct media is loaded.

Press and release the GO button to continue printing. Out of memory

The printer is out of memory. The page you are printing might be too complex for the printers memory capacity. Try lowering the resolution. See Understanding print quality settings for more information. Door open, media out, no print cartridge, or media jam

The printer is in an error state that requires operator intervention or help. Check the following:
  • The print cartridge door is completely closed.
  • Media is loaded.
  • The print cartridge is correctly installed in the printer.
  • There is no media jam.
Printer initialization

A printer initialization is taking place. No action is necessary. Fatal error

All lights are on.
  • Unplug the printer for 30 minutes, and then plug it back in.
  • If the printer still has an error, contact HP Support.
All lights are off.
  • Verify that the printer is turned on.
  • Make sure that there is power.
  • Unplug both ends of the power cord, and plug them back in.
Job Cancel

All the LEDs cycle. Canceling...(job name)

The Job Cancel button was pressed and the job is aborted. Power ON

All the LEDs cycle. Checking Paper Path and Checking Printer

This only occurs at power up. Cleaning mode/Engine test

A cleaning page or engine test page is printing.

All the LEDs cycle. Cleaning Page prints

Wait until the cleaning page is finished printing and the printer is in Ready mode. This could take up to two minutes.

Wait until the engine test page is finished printing and the printer is in Ready mode. Clearing Event Log

All the LEDs cycle.

This will happen automatically during an NVRAM Init and a cold reset. No message will be displayed. No Action is Necessary. Power On


This occurs when the product is powered on and coming out of EDOS. No Action is Necessary.

Jan 03, 2010 | HP LaserJet 1012 Printer

3 Answers

Pause & ready led blink alternatly after initilize

Check if the paper type is set correctly (in thebackside right there is a lever to set continuos paper, or single sheets).

May 03, 2008 | Epson FX 1170 Matrix Printer

1 Answer

Brother Laser Printer HL 1440

tray this
The procedure for the factory inspection mode is as follows.
(1) Turn off the printer power switch, open the front cover, and remove the drum unit.
(2) Turn on the printer power switch while holding down the control panel button. The Drum
LED comes ON.
(3) Lightly press the panel button again.
(4) Check that all the LEDs except the Ready LED are OFF.
✒ If the toner sensor is ON, the Drum LED stays ON (error).
✒ If the front registration sensor is ON, the Alarm LED stays ON (error).
✒ If the upper paper cassette sensor is ON, the Data LED stays ON. (error) (HL-1250
The lower paper cassette solenoid is turned ON/OFF even if the panel button is not pressed.
(5) Check the rear registration sensor.
✒ If the rear registration sensor is stuck backwards, the Ready LED stays OFF. (error)
✒ If the rear registration sensor is moved back and forth, the Ready LED comes ON at
any time. (error)
(6) Check that only the Data LED comes ON while pressing the panel button.
✒ If the paper eject sensor is ON, the Drum LED stays ON. (error)
✒ If the lower paper cassette registration sensor is ON, the Ready LED stays ON. (error)
If the registration sensor is ON, the lower paper cassette solenoid is turned ON, and
the Ready LED also stays ON. (HL-1250 only)
The lower paper cassette solenoid is turned ON/OFF even if the panel button is not pressed.
(7) Install the drum unit.
✒ Check that the Drum LED goes ON and the Ready LED goes OFF.
(8) Close the front cover.
(9) Continue to press the control panel button.
✒ Check that the Data LED stays OFF.
(10) Release the panel button.
(11) If all the sensors except the toner sensor are correct, the printer goes back to the Ready
If any error is detected, the printer stays in the inspection mode.

Apr 01, 2008 | Brother HL 1440 Laser Printer

Not finding what you are looking for?
HP LaserJet P2015dn Printer Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

102366 Answers

Ben Johnson

Level 3 Expert

685 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides