Question about Miele Dishwashers

1 Answer

F11 error - Miele Dishwashers

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I found a piece of wood inside the door latch mechanism and removed it. The F11 error has not appeared since.

Posted on Jan 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have my kitchen wiht a padlock on the display I am pressing the Oven light button press for a moment and comes out on the screen F11 ERROR and all the kitchen is locked I cant Use it.....please need help...


Hello Ana, thank you for allowing me to assist you!

If you are receiving an error code E11, the unit may have a shorted keypad. One of the best ways to determine if this is a false error code is to reset the power to the appliance by either unplugging it or flipping off the breaker for about ten minutes. If the error code persists, it would be advisable to reach out to an experienced appliance repair to assist further since more than likely the EOC (electronic oven control) will need replacing.

Sep 11, 2013 | Frigidaire Professional Series 24 in....

1 Answer

F11 error warning


Solution1 worked after all steps, but had to cut the power (unplug) and replug, then it startedwell ! Thanks !!!

Mar 17, 2012 | Asko Dishwashers

1 Answer

F11 blocked inlet/drain


f11 error code says in the manual
Drainage fault
Water present in appliance and is not being drained off. The display shows

Drain fault F11. The buzzer is activated for 2 minutes.

Background information:
After each drain pump step, the circulation pump operates for 2 seconds and heater pressure switch B1/13 checks the water level. If it is too high (large quantity of residual water remaining in the cabinet), the drainage time is extended. If, after a further check, the water level is still too high, then the program is interrupted, the fault code is saved and the drain pump is activated. Fault code F11 is also registered if heater relay 1K1 is not activated after the fault code F51 register check; see Section 080-3.18. Drain hose kinked. Remedy: Check the drain hose for correct positioning. Cause: Drain blocked.

Remedy:

1. Clean the on-site drain.
2. Check the sump drain.
3. Check the filters.
4. Check the heater pressure switch and replace it if necessary.

Cause:
Ball in non-return valve in sump has not opened (e.g., jammed).

Remedy:
Clean the non-return valve in the sump or replace it if necessary. Cause: Foreign objects in the drain pump.

Remedy:
Clean the drain pump and its impeller.

Cause:
Drain pump defective.

Remedy:

1. Check the voltage supply to the drain pump.
2. If correct voltage is present, check the drain pump motor winding.
3. Replace the drain pump, if necessary.

Cause:
Foreign objects in heater pressure switch.

Remedy:
Check the heater pressure switch for blockages and correct switching point.

Cause:
Heater relay defective. Heater relay (coil or contacts) becomes defective during the drainage step (after fault code F51 register check).

Remedy:
Replace the heater relay.
this is usually caused by a blockage in the drain but can also occur from other circumstances as listed above you can also see this at this link as well http://appliancehelponline.com/miele.html
if you have any further questions message me back and please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation it allows me to continue helping others in similar situations in the future Thanks again Rick

Jun 07, 2011 | Miele Dishwashers

1 Answer

Have just bought a secondhand Miele G7859 dishwasher. When turning on to any programme, it shows F11 fault code and beeps. I'll happily work through any suggestions! Thanks in advance Andy


F11 - Drainage fault

This code means that water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes.

Background information:
After each drain pump step, the circulation pump operates for 2 seconds and heater pressure switch B1/13 checks the water level. If it is too high (large quantity of residual water remaining in the cabinet), the drainage time is extended. If, after a further check, the water level is still too high, then the program is interrupted, the fault code is saved and the drain pump is activated. Fault code F11 is also registered if heater relay 1K1 is not activated after the fault code F51 register check; see Section 080-3.18. Drain hose kinked. Remedy: Check the drain hose for correct positioning.

Cause: Drain blocked.
Remedy:
1. Clean the on-site drain.
2. Check the sump drain.
3. Check the filters.
4. Check the heater pressure switch and replace it if necessary.

Cause:
Ball in non-return valve in sump has not opened (e.g., jammed).
Remedy:
Clean the non-return valve in the sump or replace it if necessary. Cause: Foreign objects in the drain pump.

Remedy:
Clean the drain pump and its impeller.

Cause:
Drain pump defective.
Remedy:
1. Check the voltage supply to the drain pump.
2. If correct voltage is present, check the drain pump motor winding.
3. Replace the drain pump, if necessary.

Cause:
Foreign objects in heater pressure switch.
Remedy:
Check the heater pressure switch for blockages and correct switching point.

Cause:
Heater relay defective. Heater relay (coil or contacts) becomes defective during the drainage step (after fault code F51 register check).
Remedy:
Replace the heater relay.

In other cases, owners found a piece of wood inside the door latch mechanism and removed it. The F11 error has not appeared since.

Hope ths helps.



May 20, 2011 | Dishwashers

1 Answer

F11 appears on the display ?? what can that be from.??


water outlet is restricted,water remains in the cabinet at the end of the cycle page 46 of your manual tells how to fix this error by reading under the care and cleaning section of your machine http://www.miele.co.uk/products/manuals/dishwashers/G1220_1230_2220.pdf note this is an older model then yours but the error codes have not changed nor has the cleaning part if you have any further questions message me back and please remember to rank how this opinion has helped in your appliance situation it allows me to help others in similar situations Thanks Rick

Mar 15, 2011 | Miele G2470SCSFSS Dishwasher

1 Answer

I have a G1220SC model. F11 shows on the panel,


F11 is a drain error.

Water outlet restricted.

** Check for kink in the drain hose.

** Clean the filter combination. (p.41)

** Clean the non-return valve (check valve) (p. 53)

** Check/clean the drain
Unplug the machine.
Disconnectthe drain where it enters the S bend from the sink. You may find thenozzle into the S bend is blocked. Probe it with a screwdriver andclear the blockage.
Plug in2_bing.gif the machine and re-try.

THIS MANUAL
may not be for your model - however it will give instructions on some of the steps above.

If all checks out - the pump will need replacement.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Dec 25, 2009 | Miele Dishwashers

1 Answer

WHAT IS F11 ERROR MIELE DISHASHER G 1232 SC


hi

this is a drain fault. you will probably find the drain spigot under the sink is blocked where the drain hose connects.

Dec 13, 2009 | Miele G892SC SS Dishwasher

1 Answer

Drain filter F11


F11 is a drain error.

Water outlet restricted.

** Check for kink in the drain hose.

** Clean the filter combination. (p.41)

** Clean the non-return valve (check valve) (p. 53)

** Check/clean the drain
Unplug the machine.
Disconnectthe drain where it enters the S bend from the sink. You may find thenozzle into the S bend is blocked. Probe it with a screwdriver andclear the blockage.
Plug in2_bing.gif the machine and re-try.

THIS MANUAL
may not be for your model - however it will give instructions on some of the steps above.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jul 07, 2009 | Miele Dishwashers

1 Answer

I have f11 error code


This is not a known error code.
Please re-check and re-post.

Thanks!!

Jan 30, 2009 | Kenmore 24 in. 16039 Built-in Dishwasher

1 Answer

CODE F11 ON MIELE 1220 SCH


I disconnected the drain where it enters the S bend from the sink. I found the nozzle into the S bend was blocked. I probed this with a screwdriver and cleared the blockage then I reconnected the drain. I turned on the dishwasher again and the F11 code was cleared. The dishwasher operated ok again.

May 14, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,861 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

icatci

Level 2 Expert

91 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Miele Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...