Question about SAMTRON 55V 15" CRT Monitor

1 Answer

No power i ploging the signalcable on the system thats soing power on otherwise not soing power. wat do i need to do?? plz suggest (model no samsung 56 v) sunil kumar sahu

Posted by on

1 Answer

Replace dl605 a three legged IC used as a 12 volt rectifer

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Not optimum mode recommended mode 1280x1024 60hz syncmaster 712 n pop up occasionly I have to shut down computer


Your video card and computer memory may not be sufficient to run in the recommended "optimum performance mode" that Samsung and Windows both suggest. Please try setting your display setting at a lower resolution such as 1080 x 760 which is still quite excellent. Otherwise you may need to buy a better video card or increase system memory to run the higher mode graphics.
Good Luck!

Jan 11, 2011 | Samsung SyncMaster 712N 17" Flat Panel LCD...

1 Answer

The monitor`s display adjustment panel is showin "CONTROL LOCKED" I cannot change any settings(like brightness,v-size,etc)... wat do i need to do?? plz suggest


Well for Sumsung with a 3% failure rate is unusual, I would try and reset to factory settings if that does not work, They have a pretty good waranty on them seeing they never break down. average is 3yr.

Jul 14, 2010 | SAMTRON 55V 15" CRT Monitor

1 Answer

MOnitor Display


1. cheak the display cable.

2. Solder the dry points on the neck board.

Dec 19, 2008 | Computer Monitors

1 Answer

Samtron 56V monitor


Its aproblem of command section.Check its components one by one.you can identify this section (the front panal buttons goes in this section and a ic in big size and pasted horizantally in the circuit).if the components are ok then change command ic with new one.This will solve your problem.

Jul 27, 2008 | SAMTRON 55V 15" CRT Monitor

3 Answers

The Red Colour Loss On My Samsung SyncMaster 753 DFX


My Dear Friends,

I Understood the problem.

I will explain it a little briefly.

There is an Integrated Chip (IC) inside the monitor which gave RED, GREEN and BLUE ( Primary Colours) to the CATHODE RAY TUBE (CRT) otherwise called monitor screen.

Due to long run, the IC might be cold soldered and one or two of the colours will not be supplied by the IC to CRT. so the CRT (monitor) will fail to display and mix the primary colours to get othe orginal colour.

The SOLUTION is to replace the IC with a new IC. As this requires a little bit expertise, please get help from the monitor service technician and ask him to replace IC with a new one. This can be done in home, so that you don't have to take the monitor to shop or service center.

All the things you have to tell the technician is to come with a stand-by ICs (NEW) for the MONITOR MODEL, in this case "SYNCMASTER 753S".

It cost around Indian Rupees 300/- for the cost of IC and another 200 Rupees for the service charge of technician.

I hope you solve this issue, if not write to me at spiceprince@yahoo.com with all details.

Spice Prince

Apr 10, 2008 | Samsung SyncMaster 753 DFX 17" CRT Monitor

2 Answers

Control locked


try this option press hold menu en arrow button to adjust setting en fix it for your best display set your resolution on 1024x768 60hz after that disable osd by removing resistor located on crt board loc# r117 tnx and good day.

Apr 04, 2008 | SAMTRON 55V 15" CRT Monitor

2 Answers

Horizontal Tearing when monitor comes out of sleep moe


Plz check memory ic of monitor in command section.
Hope this be of initial help/idea. Pls post back as requested, how things turned up or should you need additional information.
Good luck and kind regards.
Thank you for using FIXYA.

Mar 11, 2008 | CTX P772 17" LCD Monitor

13 Answers

Samtron 56V monitor


Even i was also having the same problem. We can unlock the control lock by holding the menu button for 10-20 seconds.... But now my problem is the message "Controls locked/" appears continuously. Screen width also reduced. If anyone know the solution for this please help. thanks in advance.


Surya

Oct 16, 2007 | SAMTRON 55V 15" CRT Monitor

1 Answer

Lg 563n monitor problem


Plz check your monitor's vga cable for ok .I think there is problem in 1,2,3 no pins wires continuity.If it is ok then check components thats are connecting these pin to video amp. ic on crt neck.If they are ok then change video amp. ic with new one.Hope this solution works otherwise i am always ready for help

Sep 10, 2007 | LG Studioworks 563N 15" CRT Monitor

Not finding what you are looking for?
SAMTRON 55V 15" CRT Monitor Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samtron Computer Monitors Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Richard Lilja
Richard Lilja

Level 2 Expert

355 Answers

Ted Maxwell

Level 3 Expert

3515 Answers

Are you a Samtron Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...