Question about HP PhotoSmart C4280 Laser Printer

1 Answer

Thank you That is ok I am  very grateful for your help!!!!!!!! Thank you so much!!!! the only other thing I would ask is...why would I have the wrong driver installed because I downloaded it off of the very CD that came with the printer??

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 5 achievements.


    An expert who has achieved Level 3.


    An expert that has over 500 points.

  • Master
  • 398 Answers

Oh I have read about drivers going bad, and to tell the truth I have 4 different HP printers and a scanner, I have had to download all the drivers and software of their site for one reason or another. Seems to me that I read somewhere that they can become contaminated, but there again beyond my scope of expertise.

Posted on Aug 08, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Driver seat will not move

HI Tracey, first thing to do is check the connector below the seat... make sure car is off and negative battery terminal is disconnected, the peak under the seat and check for any loose connections. If all is ok, reconnect battery and check fuses. Sounds too new for this to be a motor issue. Hope it helps.

Jan 27, 2014 | Audi Cars & Trucks

1 Answer

My master cylinder is leaking around the seal ... Wondering if i ca change the seal or it all has to be replaced

It is best to replace the hole unit thy are not very much and it would take a grate deal of experience to safely rebuild one.if you could find the parts.hope this helps ,thank you for asking fixya.have a grate day .feel free to ask any time.

Jun 15, 2010 | 1995 Chevrolet C1500

1 Answer

Ok i got a a 8GB zune and it has not been working right on tell the other day and the thing was dead for months well any way know it wont work for me agin what's wrong with it?

well it seems that u have the problem of power supply and u need to repair it and if it wont help replace it feel free to ask again thank u.

Jul 27, 2009 | Microsoft Zune JS8-00001 Digital Media...

1 Answer


thank you for letting me know the provider helped correct the problem

Feb 07, 2009 | Compaq Computers & Internet

1 Answer

Logitech r-20 Speakers


Appreciate the direct "Ask Me".

It would seem that the documentation where you sourced the info S-Series Ultra Durable Motherboard. 945PL-DS3/S3 (rev.2.0) is intended for a number of different models. From what I can gather, you have a Giga-byte motherboard either a GA-945PL-DS3, GA-945PL-S3 or a GA-945PL-S3E all Rev. 2.0.

Assuming that it is a 945PL-DS3 (rev. 2.0), then the audio driver would be "Realtek Function driver for Realtek Azalia audio chip (Including Microsoft UAA Driver)". Pls verify if it were so.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 27, 2008 | Logitech R-20 Computer Speakers

1 Answer

Recently changed printer to a DCP-135C,can't get it to printout anything. can u help?

Hello Harpalis,

Have you installed the latest drivers for your new printer? Also make sure that you have uninstalled the previous printer's driver using the "Add/Remove Software" in Control Panel.

Once you have done this, make sure all cables are secure between printer and computer. Next make this as your default printer. Procedure as follows..

In Control Panel, go to printers and faxes. you should see your printer here. Just right click and choose "set as default printer". Sometimes your driver software will ask this during installation itself. You should be OK now...

Should you have any further questions, please feel free to post them here. Please do not assign a rating until you feel your problem is resolved. I will try my best to help you further if need be.

If you are satisfied with my solution or have no other questions, please close the problem by assigning a FIXYA rating for my solution. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!


Apr 19, 2008 | Office Equipment & Supplies

1 Answer

Nokia keypad not working

Try to find a website by searching the model then try to take the phone apart so you can see what is wrong with the bottom of the keypad.

Jun 30, 2007 | Nokia 6233 Cellular Phone

Not finding what you are looking for?
HP PhotoSmart C4280 Laser Printer Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

1089 Answers


Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides