Question about Yamaha GO46 Sound Card

1 Answer

Audio from go46

Hey man, I am trying to do 4 outputs and its playing on two channels. Like if I plug my korg triton into it, it only plays on the left side. Its not playing in stereo. What can i do. my email address is jchaffen@yahoo.com

Posted by on

  • Michael Chaffen
    Michael Chaffen Jun 16, 2009

    BUt i saw the motif work great on it with no problem

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds you have 2 channels set on stereo maybe not mono ?

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The left channel of my toneport is higher than the right side in the outputs...even in the headphones its the same. When i push play with very low volume i start listening first on the left channel. I...


Check out your speaker settings in Sounds and Audio devices, in your control panel.

Start - Control panel - Sounds and audio devices - Check the speaker volume under the "volume" tab and the volume controls for audio playback under the "Audio" tab.

Jul 03, 2010 | Line 6 TonePort UX2 Sound Card

1 Answer

All of a sudden my Echo Indigo DJ soundcard will play both virtual CD players on my PCDJ software on one channel. For a while, I had cd 1 on one channel and cd2 on the other. I am using a pig tail plug...


I can run audio on 3 separate channels/outputs of my laptop

I use Tricerasoft Swift Elite DJ software but the areas you need to look at for troubleshooting are probably similar:

1) check the (PCDJ) software settings for selecting the channel outputs of your Indigo DJ on each deck/ player. NOTE: 1/2 and 5/6 are the same physical port (headphone port), while 3/4 and 7/8 are also shared on the Line Out port. So make sure you use for eg. one player uses 1/2, and the other player uses 3/4 ONLY IF you want them running out to separate channels on the mixer

I personally run both my decks off the same channel, ie 3/4 so that my software can do the mixing for me. My mixer only acts as an master control device where everything else connects

2) Make sure you check your IndigoDJ Console (installed to the Windows Start menu under Echo Audio, Indigo DJ), if you have any conflicts or if for some reason one particular channel pair gets inadvertently muted, resulting in no sound coming from the port.

3) I also use my onboad sound card (typically for previewing music or for an auxillary output). This is obviously controlled by the Operating system... in Windows is is through the Sound properties, default sound device. I recommend NOT using Indigo DJ as a default sound card -- but that is a personal preference.

So in this way you actually have 3 outputs for sound

As far as cabling is concerned, it depends on what you are connecting to. I use a 1/8 (mini computer) jack to 1/4 whcih then plugs into a direct box (eleminates any static hum etc), then from the DI box using an XLR cable to the mixer. Your setup may be slightly different.

Hope this helps!

Dec 01, 2008 | Echo Indigo DJ Sound Card

1 Answer

Yamaha GO46 firewire audio interface


Hi. It might be a bit late, but the solution to your problem is the fact that the phones level is dependent on output 3-4. If you turn 3-4 all the way up you should be able to hear something. You might want to route all the outputs to the digital mixer.

Aug 23, 2008 | Yamaha GO46 Sound Card

2 Answers

Phones 1-2 has both channels coming out of it


Had the same problem and fixed it today. It is the mute button. Whem you change from 1-2 to 3-4 if the mute button for 1-2 does not activate you will get the sound from 1-2 thru 3-4. Just change the setting and you are away. worked for me.

bruce

Jun 03, 2008 | Echo Indigo DJ Sound Card

1 Answer

Sound card freezes up


Buy enternal power supply for it.
9 Volts
1000mA
But mind that it should be psu with REGULATED output(steady 9Volts).

Apr 25, 2008 | M-Audio Fast Track Pro External Sound...

4 Answers

Yamaha GO46 is not recognized as an audio device - wdm driver not instaled properly


get a new soundcard GO46 is a bag of trouble. I had to get a special Firewire Card with a Texas Instrument chip, since the cheap internal firewire interfaces don't work with this card. Also make sure you are not running XP64, since it is not supported. good luck

Mar 27, 2008 | Yamaha GO46 Sound Card

1 Answer

Surround center speaker does not work


This is a 5.1 (6 Channel Technology) You should hear only the voice thro the center speaker. If the source you are playing is stereo, however the software splits the source its difficult to seprate the voice track, if the source is a DTS 5.1, then you should hear the voice only thro the center speaker. eg: when you play a DVD movie which is DTS 5.1 then you should hear only the voice track in the center speaker, if the dvd movie is just stereo then you will not hear any audio in the center speaker, while the other four speakers get output, this is the special effect in 5.1 ( 6 channel Output).

Dec 27, 2007 | Inland 58019 ThunderSound 5.1 PCI Sound...

1 Answer

Powerbook doesn't recognize Yamaha GO46 FW interface


Hello. I had the same problem and solved by mere casuality. If you disconnect the AC power adaptor and let the Firewire connection to be the only power supplier, then the GO46 will be inmediately recognised by the "Preferences -> Sound" panel of the G4.

Hope I've been helpful. Bye.

Oct 27, 2007 | Yamaha GO46 Sound Card

Not finding what you are looking for?
Yamaha GO46 Sound Card Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Cards Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Terry Allen
Terry Allen

Level 3 Expert

680 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Yamaha Audio Card Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...