Question about Panasonic PT-L785U Multimedia Projector

1 Answer

Projector posted error, "replace bulb" Projector

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 59 Answers

Your projector need replacement of lamp unit if you don't want yet you just reset the lamp counter

procedure:
Power on projector
press MENU key
Press right arrow key to select Option
Press down arrow key to select lamp Hours
Press and hold down the ENTER key 5 second (lamp hour counter show red)
press POWER button to turns off the projector
now you power on your projector and no error displaed and no itself turn off after 15 minutes

Posted on Apr 18, 2011

Testimonial: "This is great news! Unfortunately I have already purchased a new lamp. It's probably good to have a spare on hand."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Temperature light comes on after replacing bulb.


I am experiencing the exact same problem. hope someone comes on worn a solution. projector worked fine before replacement - all fans have been cleaned and are working properly. ..

Mar 31, 2014 | Mitsubishi HC3800 1080p Home Theater DLP...

2 Answers

Compaq MP2800 DLP Projector


If the projector is not getting a source it might go on standby maybe check where you plug it in.
Projectors require quite a bit of power and should be on a single loop/outlet not hooked up to a powerbar with more things on it.

Hope that helped.

Dec 26, 2007 | Compaq MP2800 Microportable Projector sps...

1 Answer

Projector suddenly went unresponsive


open the bulb assembly and check if the bulb has fused / broken into pieces.if not then the ballast unit that powers the bulb is at fault and needs replacement
if the bulb has fused/broken , then probably the bulb that u had replaced 3 months back wasnt genuine!

Jan 18, 2013 | Panasonic PT-AE700U Multimedia Projector

2 Answers

I have a Benq w710st DLP projector and when i turn the power on after a minute it turns off. The power button turns off and both the lamp and temp lights turn red. How do I fix this and can I do it my


Like a previous post I too had the same issue with my Benq MW516 - after a 15 minutes working the light would turn off and the TEMP and LAMP lights come on red and would not turn off until the unit was turned off. I found the problem was a very dusty cooling fan for the light bulb and after using compressed air (do NOT let any fan spin up - this can damage the fan, hold it and rotate slowly after unplugging it from the logic board first). Once I dusted out the entire projector it is back to running just fine.

benq_mw519_lamp_fan_dusty-iybpcirgr4diztiimt1zeukr-1-0.jpg

benq_mw519_lamp_fan_remove-iybpcirgr4diztiimt1zeukr-1-1.jpg

Jan 06, 2013 | BenQ W710ST 3D HD Short Throw DLP...

1 Answer

XL-2100U lamp cycles on and off


Hi

I recently had a similar problem after replacing my lamp the set would work for 22 mins then go into standby for 30 sec then come back on, then repeats, I decided to experiment with the lamp housing, I removed the new lamp, unscrewed the top of the lamp that holds the actual bulb then switched out the main housing (bottom part) with the original housing, that seemingly has corrected my problem, you may want to try if the replacement lamp did not come from Sony...good luck

Sep 10, 2008 | Sony LAMP BLOCK XL2100U Projector Lamp

1 Answer

My Panny AE700U shut down & won't restart


HI there

This is a faulty Mainboard that will need either repair or replacement.

If a Projector starts playing on and off tricks I have found it to be 99% of the time a faulty Mainboard.

Apr 13, 2008 | Panasonic PT-AE700U Multimedia Projector

1 Answer

C20x lamp error


Hi,

This is due to thermistor problem. Near to the lamp one thermistor will be there please check connectivity. if it is failed please change the same.

Regards,
prakasam

Mar 05, 2008 | Sharp (BQCPGC20X1) Projector Lamp for...

1 Answer

Sharp Projector XV-Z90 Flickering


the color wheel is dirty. It just need to be cleaned.

Feb 18, 2008 | Sharp Projector lamp Projector Lamp

Not finding what you are looking for?
Panasonic PT-L785U Multimedia Projector Logo

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Shannon Murphy

Level 1 Expert

2 Answers

HEMANT GROVER

Level 2 Expert

171 Answers

Are you a Panasonic Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...